TABLE OF CONTENTS Receiving and Inspecting 3 Unpacking 4‐6 Safety Instructions 7 Specifications 8 L Soaking Tub Drawings 9 Installation Procedures L Drain 10 ...
If the crate is in good condition or with minor imperfections and there is a suspicion that the material inside may be damaged, please record it on bill of lading and ask the shipping agent to sign it. You must keep a copy of the bill of lading. In most cases, the minor damages to the surface of the packaging may not affect the product, but any signs of defects must be recorded with the shipping agent present. All product damages must be reported within 24 hours of receipt from Ella's Bubbles or its Vendor. Claims WILL NOT be processed if the proof of the damage is not reported within 24 hours. ...
UNPACKING AND INSPECTING THE PRODUCT 1. Remove screws and nails from the wood crate with care so the cardboard packing is not damaged. Please retain the wood crate and parts until satisfactory inspection of the product has been done by the installer. 2. Remove the cardboard packing with care. Retain the carton and bubble wrap packing until satisfactory inspection of the product has been done by installer. The original packing is required in case of returns or exchanges. Be careful not to scratch the surface of the bathtub on exposed staples, nails, or any tools. 3. Remove the end access panel before removing the product from the crate. Remove the screws from the tub legs supporting the tub frame to detach the tub from the crate base ‐ never lift the bathtub by the plumbing fixtures or parts! Lifting or pulling plumbing parts will result in product damage and water leakage and will void your walk‐in bathtub warranty. Lift the tub only by the frame or bathtub shell. Do not lift the tub by the wall panels or any parts to avoid damage. Also, make sure not to damage the parts like drain on the bottom of the tub while carrying the tub (some of these parts are on the bottom of the tub, and will be exposed). 4. Inspect the shell and bathtub components. If any defects or damages are found on the acrylic finish of the tub, or if there is visible damage to the components, do not install the bathtub. Damages or defects to the finish claimed after the walk‐in bathtub is installed are not covered by the Ella’s Bubbles warranty. Ella’s Bubbles assumes all responsibilities for any damages to the product prior to, and throughout delivery, and will cease upon reception of the walk‐in bathtub. Refer any claims for the damages to the carrier. For warranty details, refer to the warranty information located at the end of this manual. READ THESE IMPORTANT SAFETY INSTRUCTIONS COMPLETELY BEFORE INSTALLING AND USING YOUR PRODUCT. YOU MUST FOLLOW ALL INSTRUCTIONS IN THIS MANUAL. FAILURE TO DO SO WILL RESULT IN YOUR ASSUMPTION OF LIABILITY THAT MAY OCCUR BY SAID INSTALLER. FAILURE TO COMPLY WITH ALL INSTRUCTIONS CAN RESULT IN PRODUCT DEFECT AND ...
IMPORTANT SAFETY INSTRUCTIONS WARNING When using this product, basic precautions should always be followed. Read and follow all instructions pertaining to risk of fire, electric shock, and/or injury. Use this unit for its intended purpose, or as described in the manual. Use only the parts and attachments provided, or as recommended by the manufacturer. Temperature in excess of 100.4F (38 Celsius) may be harmful to your health. Check and adjust the temperature before use. Avoid the use of alcohol, drugs, or medication while using your walk in tub. Consult your physician before using the whirlpool/air system if you are pregnant and/or have a heart condition. People using medications, herbal remedies, sleep aids, and/or having adverse medical history should consult a physician before using this product. DANGER: To reduce the risk of injury, do not permit children or persons with disabilities to use this product unless they are closely supervised at all times. To avoid injury, exercise caution when entering or exiting the walk‐in tub. Never drop or insert any objects into any openings. Risk of electric shock: Do not permit electric appliances (such as a hair dryers, lamps, telephones, radios, televisions, etc) within 3 feet (1.5m) of the tub. Traction enhanced, textured bathtub floor must remain clean to minimize slippage. The Ella’s Walk‐In tub is not intended for any outdoor use. Install the unit in accordance with the instructions included in this manual. Please use a licensed contractor and plumber for installation. Avoid using your heated tub after strenuous or excessive exercise. As the installation manual details – do not use abrasive materials to clean Ella’s acrylic tub finish. Do not submerge body in heated tub for extended periods of time to avoid hyperthermia; The symptoms of hyperthermia include an increase in body temperature which can result in dizziness, lethargy, drowsiness, and fainting. ...
SPECIFICATIONS Actual Size: 29 ½” W x 55” (ext. 59”) L x 40 ½” H Net Weight: 145 lbs. Shipping Size (In Crate): 32” W x 60” L x 48” H Shipping Weight: 255 lbs. Water Capacity: Approx. 75 gallons Ella’s Soaking Features: 1. Acrylic Tub shell: • High quality cast acrylic grade A; • Excellent color uniformity; • 5mm cast acrylic sheet; • Easy‐to‐clean, gloss finish (white); • Fiberglass gel coat reinforced. 2. Low threshold step in. 3. Seven adjustable stainless steel heavy duty leveling legs. 4. Stainless steel and tempered glass door, door frame & rubber seal. 5. Two built in safety grab bars. 6. Wall extension kit to fit in standard 60” opening (extends to 59 inches). 7. Two (2) front and one side removable access panels. ...
DRAIN ‐ SUBFLOOR ‐ DOOR ‐ SEAL PROTECTING THE TUB: Cover and protect the bathtub shell and fixtures from scratches or other damages during the tests and installation. DRAIN: Insure that the drain rough has been placed at the proper location. See specifications and drawings. The dual drain can be connected with a T or Y connector in to 2” or 1 ½” of existing house drain. Materials must be used based on local plumbing code requirements. Note that flexible drains are not allowed in some states. The customer and contractor are responsible for using the appropriate materials per code. SUBFLOOR: Prepare the subfloor for the drain and ensure that area is level. The supporting subfloor must be able to support the total weight of the bathtub, bather and water. Use a leveler and make sure that the subfloor below the tub is leveled. If the floor is not perfectly level, adjust all 7 leveling legs to realign the tub to a perfect level. It is important that all 7 leveling legs are completely supporting the tub (touching the floor) and the tub is leveled for the door seal to work properly. If the tub is not perfectly leveled, it could result in water leakage and void the warranty. Adjust the legs and lower the tub to the floor base, to within 1/16 if an inch within above the floor or tiling. Lower the tub as much as possible and seal with a caulking, if appropriate. f the subfloor does not support the total weight of the bathtub, bather, and the water, it can result in warping of the shell, misalignment of the door, and/or create leaks or damages to the bathtub and/or the building structure. ...
DRAIN ‐ SUBFLOOR ‐ DOOR – SEAL cont… SERVICE ACCESS AND VENTILATION: It is the responsibility of the installer or owner to provide access for service required, per code. Ella’s Bubbles is not responsible for any costs related to obtaining access for repair. The owner shall assume responsibility for such costs, and if appropriate, must seek recovery from the installer. DOOR AND SEAL: Please keep in mind that the door has been closed for an extended period of time throughout shipping and the tub has been stored in various temperatures. When the tub is received, the door seal must be reformed and adjusted, as it may have possibly stuck to the frame throughout storage and shipping in various temperatures. In cases such as these, the door seal must be released and rested with the door open. It can be done by squeezing the seal with your finger tips and pulling it away from the door frame to regain its flexibility and original form. It is highly suggested that the door be kept in the open position while the tub is not in use to increase the lifetime of the door seal and maintain its flexibility. TESTING YOUR WALK IN TUB All walk‐in bathtubs are factory tested for proper operation and watertight connections prior the packing and shipping. However, the unit must be retested by installer prior to installation. Ella’s Bubbles is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure. 1. Place the walk‐in bathtub on a level surface near appropriate water and electrical supply and drainage. It can be done in homeowner’s driveway or in the bathroom, as well. 2. If the tub comes with a flex drain, connect it to the existing home drain. If not, run a temporary drain. Fill up the water 2 inches below to overflow hole. 3. Do not install the bathtub if leaks are detected. Caution: If walk‐in bathtub is not resting on all six leveling feet, water will not drain properly and may cause the door to leak. Never allow the weight of the tub to be supported by wood support stringers as this will result in product failure and void the warranty. Verify the product is completely level by checking the tub deck surface and ensure all 7 leveling feet are touching the ground. Every tub is 100% water tested at the factory with all pumps in working condition. However, transporting or carrying the tub may cause loose fittings, possible damages, or leaks. It is the contractor’s responsibility to water test the bathtub with all pumps running prior to finishing the tub and wall installation. The contractor must make sure that all fittings by the pumps are retightened and the tub is leak proof. Any water or air jets can be retightened to stop the leaks. ...
FINISHING INSTALLATION Almost any PVC pipe leaks can be easily fixed with plumbing epoxy putty sold at any hard ware store if needed. After the all water testing is completed, and all fixtures are checked, the tub can be installed to the surrounding wall, or walls. Ella’s walk in tubs come a with low rise tile flange which allows 2 wall or one wall installations. The extension panel of the tub can be installed as needed for 60” openings. The tub can be finished and tiled over as shown in images. Caulking must be applied to joints as needed after the tub is installed. Note: The shower curtain and raise rod for the hand mixer can be installed per customer’s responsibility. Any alterations or installed additions are the responsibility of the installer. Ella’s Bubbles is not responsible for any damage to the unit or for water damage which might occur due to improper installation. ...
OPERATING INSTRUCTIONS 1. Enter the walk in tub, close the door and secure the safety chrome lever in the down position to ensure the closure of the door. The door can locked with the handle from a seated or standing position. Do not apply any body weight on the door when entering and exiting the tub. The door and the door hinges are well built and are very durable. However, leaning on or applying users weight on the door may damage the door by changing the alignment of the door and creating water leaks. Such damages are not covered by the warranty. It is recommended to leave the door in the open position when the tub is not used to extend the life of the seal. 2. To fill up the bath tub with water, adjust desired temperature of the water. 3. Fill walk in tub as desired or 2” inches below the over flow holes inside the walk in tubs. 4. To exit the walk in tub simply open the dual drain over flow switches and your tub shall drain in 80 sec or less. 5. Once the walk in tub is completely empty you are safe to exit the walk in tub. 6. There are no user serviceable parts located under the tub (behind the removable access panels). 7. Usually, a mild detergent will remove construction debris. More stubborn debris may be removed with denatured alcohol, or Clorox Soft Scrub cleaner. Light scratches and dulled areas may be restored to original luster by rubbing with a fine grade automotive type cleaning and polishing compound. CLEANING AND MAINTENANCE It is recommended that once a month, unscrew (counter clock wise) the suction cover and clean away any hair, lint or debris from the cover and housing ‐ Then remount the cover in place. Never operate the unit with the safety suction cover off. Do not use abrasive cleaners, as they will scratch and dull the surface of the acrylic. Plaster can be removed using a wooden edge. ...
WARRANTY • The bathtub shell, frame and finish are covered by a limited lifetime warranty. • The door is covered by a limited lifetime warranty under normal use and conditions. • All supporting equipment, door seal, waste and overflow are covered by a limited five (5) year Warranty. • This warranty is nontransferable and applies only to the original owner. • Additional servicing is not warranted by the factory (manufacturer). Additional servicing i.e.(services that extend or are not included in the manufacturer’s (5)yr warranty). CONTACT INFORMATION • Toll Free 1‐800‐480‐6850 • www.ellasbubbles.com • info@ellasbubbles.com ...
WARRANTY ACTIVATION REPORT Page 1 MODEL: Ella’s Soaking SERIAL # _______________ PURCHASE DATE:________________ PURCHASE PRICE:____________________ PLACE OF PURCHASE:___________________________________________________________ CONTACT NAME:______________________ PHONE NUMBER:_____________________ Upon the complete installation of the Ella’s Walk In Bathtub, the following Warranty Report must be completed and returned to Ella’s Bubbles, LLC. in order for the Warranty to be activated (faxed, scanned and emailed or hard copy mailed).
Page 17
WARRANTY ACTIVATION REPORT Page 2 OWNER’S INFORMATION: _____________________________________________________________________________ Name _____________________________________________________________________________ Address City State ____________________________ _________________________________________ Telephone E-mail ___________________________ _________________________________________ Date Signature INSTALLER’S INFORMATION: _____________________________________________________________________________ Company Name Installer’s Name _____________________________________________________________________________ Address City State ____________________________ _________________________________________ Telephone E-mail ___________________________ _________________________________________ Date Signature To activate manufacturer’s warranty please use one of the options below: Via mail: Ella’s Bubbles, LLC.