Adjusting The Sensor; Door Lock, 3-Pin Connector; Adjusting The Sensor With The 1Way Remote Control - Python 872 Owner's Manual

H3/6 RED
H3/7 PINK/WHITE
H3/8 PINK/BLACK
H3/9 RED/BLACK
H3/10 NC

Door Lock, 3-pin connector

1 BLUE
2 EMPTY
3 GREEN

Adjusting the Sensor

Important! The vehicle system must be disarmed and the vehicle doors, hood, and trunk should remain closed
and ignition off or the unit will exit adjust mode prematurely.
Adjusting the sensor with the Responder LE remote control:
1.
Press and hold the
beep after 3 seconds) or until the amber LED turns on and you hear one long beep.
2. Press and hold the
one long chirp, confirming that it has entered adjustment mode.
3. Press the , or
remote will light up according to the level that is set.
AUX
AUX
Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the siren
chirps, indicating the impact level required to fully trigger the alarm.
• button: Pressing this button increases the sensitivity one level. The siren chirps twice confirming the sen-
sitivity adjustment.
AUX
•
button: Pressing this button decreases the sensitivity one level. The siren chirps once confirming the sen-
sitivity adjustment.
AUX
• button: Pressing this button resets to default level 7. The siren chirps three times.
AUX
To exit the shock sensor adjustment mode from the remote control:
Press and release the
1.5 seconds in the main menu to exit programming.

Adjusting the sensor with the 1way remote control:

1. Disarm the system, turn the ignition Off and close all the doors.
2. Press and hold the
Select beep after 3 seconds) or until the amber LED turns on.
3. Press and hold the
module emits one long chirp, confirming that it has entered adjustment mode.
4. Press the , or
Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the
AUX
AUX
siren chirps, indicating the impact level required to fully trigger the alarm.
• button: Pressing this button increases the sensitivity one level. The siren chirps twice confirming the
sensitivity adjustment.
AUX
• button: Pressing this button decreases the sensitivity one level. The siren chirps once confirming the
sensitivity adjustment.
AUX
• button: Pressing this button resets to default level 7. The siren chirps three times.
AUX
To exit the shock sensor adjustment mode from the 1 way remote control:
Press and release the
for 1.5 seconds in the main menu to exit programming.
© 2009 Directed Electronics. All rights reserved.
Port Switch
IGNITION 1 +12V INPUT (30A FUSED)
1
(30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire)
(87a) FLEX RELAY INPUT (key side of ign, acc or starter wire if needed)
1
ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED)
1 8
No Connection
1 5
1 3
(-) 500mA UNLOCK OUTPUT
NOT USED
(-) 500mA LOCK OUTPUT
AUX
button of the remote control for 8 seconds (If Car 2 mode is on, ignore the Car Select
button 1.5 seconds or until the amber led comes on solid.- The control module emits
AUX
buttons to adjust the sensor level. When adjusting the sensor, the Ghost LED's on the
AUX
AUX
button any time during programming to go back to the main menu. Press and hold for
AUX
button of the remote control for 8 seconds (If Car 2 mode is on, ignore the Car
button 1.5 seconds or until the amber led flashes then comes on solid.- The control
AUX
buttons to adjust the sensor level.
AUX
AUX
button any time during programming to go back to the main menu. Press and hold
Start In Unlock Output Port
10 9 8 7 6
12
5 4 3 2 1
10
1
Port Port LED
12
R
4 3
ELECTRONICS 2 1
TACH LEARN THREASHOLD
JMP1 OFF ON
7