Related Manuals for Eagle power Hospital S6101HQ-T
Summary of Contents for Eagle power Hospital S6101HQ-T
- Page 1 HOSPITAL VAC MODELS: S6101HQ-T S6101HQ-S OPERATIONS AND PARTS MANUAL IMPORTANT! READ THIS MANUAL PRIOR TO USE...
- Page 2 TABLE OF CONTENTS Important Safety Instructions ............. 1 Operation ................... 4 Assembly Instructions ............... 5 Maintenance ................6 Servicing the Vac Motor ............. 7 Part Diagrams ................8 Warranty Information ..............14...
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine. -
Page 4: Save These Instructions
WARNING: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor. WARNING: Use of this machine to move other objects or to climb on could result in injury to the operator or damage to the machine. - Page 5 Page 3...
-
Page 6: After Use
1. Attach paper bag to tank inlet deflector. See Figure 1. 2. Ensure that the cartridge filter is securely attached to the bottom of the vacuum head. See Figure 2. For S6101HQ-T units, insert basket filter into the tank. Figure 1 See Figure 2-A. - Page 7 POWER HEAD AND WAND ASSEMBLY INSTRUCTIONS Locking Collars 1. Slide on the two collars as pictured. See Figure 1 2. Insert wand into the power head neck until it stops. Slide the small collar into the neck of the power head. Screw the large collar onto the powerhead until tight.
-
Page 8: Servicing The Filter
SERVICING THE FILTER The filter is accessed by lifting the head assembly off the tank. Cartridge filters - Remove the filter retainer by turning the black knob 90 degrees counter-clockwise. Cartridge filter will then slide off. NOTE: Be sure to frequently clean the filter Worn filters can affect vacuum performance. -
Page 9: Carbon Brush Replacement
SERVICING THE VAC MOTOR CARBON BRUSH REPLACEMENT (Replacement Carbon Brushes: Part #S8053200) Disconnect power cord from power source. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. Remove the screws that attach the inner cover to the head assembly and set aside. - Page 10 VACUUM MOTOR ASSEMBLY (S6101 HQ-S) POS. PART # DESCRIPTION S81122 ELECTRIC CORD, 3 X 16 AWG S80138L STRAIN RELIEF "L" S80139 CLAMP, CORD S81006 SCREW, (PHILLIPS) M5 X 20 S83444 TERMINAL BLOCK S82928AU HANDLE BASE S82627 SCREW, (PHILLIPS) M5 X 40 S82927 HANDLE, BLACK S81026...
- Page 11 VACUUM MOTOR ASSEMBLY (S6101 HQ-T) POS. PART # DESCRIPTION S81122 ELECTRIC CORD, 3 X 16 AWG S80138L STRAIN RELIEF "L" S80139 CLAMP, CORD S81006 SCREW, (PHILLIPS) M5 X 20 S83444 TERMINAL BLOCK S82928AU HANDLE BASE S82627 SCREW, (PHILLIPS) M5 X 40 S82927 HANDLE, BLACK S81026...
- Page 12 TANK AND CART ASSEMBLY (S6101HQ-T) POS. PART # DESCRIPTION S82652A INLET COVER S82846 GASKET S82593 DEFLECTOR, TANK S82585 RETAINER, TANK ADAPTOR S86132G5-NE TANK S81026 SCREW, (PHILLIPS) M5 X 30 S81302 RIVET, M5 X 19 S83602 CLAMP, TANK, COMPLETE POS. PART #...
- Page 13 TANK AND CART ASSEMBLY (S6101 HQ-S) POS. PART # DESCRIPTION S82652A INLET COVER S82846 GASKET S82593 DEFLECTOR, TANK S82585 RETAINER, TANK ADAPTOR S86039G55-GP TANK S81026 SCREW, (PHILLIPS) M5 X 30 S81302 RIVET, M5 X 19 S83602 CLAMP, TANK, COMPLETE POS. PART # DESCRIPTION S86045...
-
Page 14: Power Head Assembly
POWER HEAD ASSEMBLY POS. PART # DESCRIPTION POS. PART # DESCRIPTION VCA1CFSNEP TOP COVER VCA1BAS350 BASE SCREW SCREW USE KIT VCSA8VTEL USE KIT VCSA8VTEL SCREW VCA1SUPRSX RIGHT SIDE PLATE, ROLLER BRUSH USE KIT VCSA8VTEL VCA1CABCC CLAMP, CORD VC1108035000 BEARING VCSA3MO3P VCSA4R3N1 CONNECTING TERMINAL, COMPLETE 1 ROLLER BRUSH, COMPLETE (INCL 03, 04, &... -
Page 15: Recommended Spare Parts
TOOLS POS. PART # DESCRIPTION S76158 WAND, CURVED S76240 WAND, STRAIGHT S70617 CREVICE TOOL S70004 ROUND BRUSH S70616 HAND TOOL S70632 DOUBLE USE BRUSH S71685 HOSE FILTERS S80147 Paper Bags, Pack of 5 S82881 Hepa Filter, Cartridge S82677 Poly Basket Filter RECOMMENDED SPARE PARTS S8053200 Replacement Carbon Brushes... -
Page 16: Warranty Policy
Warranty Policy Limited Warranty Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and workmanship under normal use and service to the original purchaser as detailed below. 10 Years Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be free from defects in materials and workmanship for a period of ten years.