Related Manuals for Essex Electronics Encoded Keyless Entry
Summary of Contents for Essex Electronics Encoded Keyless Entry
- Page 1 KPX-34-ERM3 INSTALLATION & INSTRUCTION MANUAL Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 2 All rights reserved. No part of this documentation may be repro- duced in any form, without prior written consent of Essex Electron- ics, Inc. Essex Electronics shall not be liable for errors contained in this manual. The information in this document is subject to change without notice.
-
Page 3: Table Of Contents
Programming Individual Users ............ 21 KPX-34-ERM3 Series Diagrams ..........28 ERM Circuit Board ............... 28 Typical Hook-up Fail Safe or Fail Secure and CCTV Diagram .. 29 Warranty & Repairs ..............32 Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 4 Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 5: Introduction
! ! ! ! ! 3x4 Keypad with ERM KPX-34B-ERM3 Brass Finished* Bezel KPX-34S-ERM3 Stainless Steel Bezel KPX-34K-ERM3 Black Bezel *Bezel is brass in appearance. Actual bezel is PVD-coated stainless steel. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 6: Specifications
(see page 13) and reading codes or to a printer for real-time print-out of activities. A serial cable or serial to USB cable is required and not included. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 7: Erm Configuration
3. Second Door - Users can be assigned to open a 2nd door. 4. Doorbell - Press # at the Keypad to trigger a 1 second output for a doorbell (not included). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 8 4. Internal Alarm System - Detect Break-in, Door-ajar & Tamper. 5. Doorbell - Press # at the Keypad to trigger a 1 second output for a doorbell (not included). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 9: Keypad Connector Diagram
Door Ajar Time setting. RED, BLACK, GREEN, VIOLET, GRAY, ORANGE and SHIELD- These wires all connect to the ERM module. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 10 User from the security level. All “exempt” users can get in with either a code or a card no matter what the security level is set for. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 11: Keypad Configuration
#. To change the audible beep, proceed as follows. Otherwise, go to Step 5. To change the audible beep, enter Code Audible Beep 201 # Normal Beep (factory default) 200 # Short Click (quieter) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 12 2. Jumper the two pins above the connector labeled "CONFIG.” 3. Apply appropriate power. (You should hear 4 beeps and the RED LED will flash and the GREEN LED will be solid). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 13 8. Re-apply power. 9. Press PROGRAM button in the ERM to establish the encoded connection. This will put the system into setup mode. 10. Press * * to exit. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 14: Normal System Operation
Output as Aux.) to Turn Output A ON (2 Output as Aux.) to Turn Output B OFF (3 Output as Aux.) to Turn Output B ON (3 Output as Aux.) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 15: Tamper Alarm
If communication is lost for more than 2 seconds, the unit goes into LockUp Mode and can only be restored to Normal Operation by pressing the PROGRAM button. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 16 When using Output B relay as an Alarm, and since the output is on to indicate a Non-Alarm status, a loss of communication or invalid EC will always create an alarm indication. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 17: Using The Kpx-34-Erm3 With A Pc
Installing the CD-ROM ! ! ! ! ! Install the "Essex EZKey Software" program from the enclosed CD. The files will default to C:\Program Files\Essex\EZKey unless otherwise re-directed. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 18: Using Keypad Programmer Software (Keyprog)
If there are conflicts (e.g., two User Number 1’s), you will be asked to select a resolution. Once complete, you will need to save the chart and upload to the Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 19: Using Keypad Logger Software (Keylog)
Select “Options” and “COM Port.” Alarms Loss of power- reported when power is restored. Tamper Alarm- 4 incorrect code entries Loss of communication between Keypad and ERM (Keypad removed or broken connection). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 20: Programming The Kpx-34-Erm3 With The Keypad
ERM board. This will take you to Step 3 of Programming System Setup. Once you enter setup mode, you have 30 seconds to begin the program sequence. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 21 Double Slow Flash Slow Flash Triple Slow Flash Solid Configuring Output A (Default: Aux #1) a. Enter b. Select one of the following: CCTV / External Light 1) Enter Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 22 Keypad Status After Step Completion Step Beep Red LED Green LED Double Slow Flash Slow Flash Double Slow Flash Fast Flash Triple Slow Flash Solid Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 23 Timed- Enter the desired time interval in hours (1-98), followed by Example: 5 # 3 # 5 # 9 9 # (Sets Second Door with 5 second Door Open Time and Manual Latching) Doorbell 1) Enter Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 24 Baud Rate to 9600 if connected to a PC (default) 4. Enter to complete the sequence and reset the system to normal operation. Note: If using a printer or Hyper-terminal, will print Setup Configuration Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 25: Programming Individual Users
Program or Delete Users Authorization Output A Authorization (see notes) 2nd Door (see notes) Output B Authorization (see notes) 3rd Door (see notes) Exempt from Security Level restrictions (see notes) Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 26 Security Level restriction requires an external time clock or keyswitch. This allows you to restrict access to Users who are not exempt. See Clock Input on pages 6. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 27 Modify a User by User Code a. Enter b. Enter the User Code for the User you wish to modify, followed Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 28 Note on Modifying Users: Once you have begun to modify a User, previously programmed authorizations are deleted for this User. Modifying a User with a Card a. Enter b. Present card Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 29 If no more Users are to be deleted, enter and return to Step 3, or if you have completed all User Programming, enter second time to complete programming sequence and reset system to normal operation. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 30 You are now back to Step 3 (page 21). Deleting a Temporary User a. Enter b. You are now back to Step 3 (page 21). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 31 Steps 1 & 2 each time. However, if more than 30 seconds elapse between each step during programming, the system will reset and you will have to start from Step 1. Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 32: Kpx-34-Erm3 Series Diagrams
KPX-34-ERM3 Series Diagrams ERM Circuit Board ! ! ! ! ! Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... -
Page 33: Typical Hook-Up Fail Safe Or Fail Secure And Cctv Diagram
Typical Hook-up Fail Safe or Fail Secure and ! ! ! ! ! CCTV Diagram Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com... - Page 34 Notes Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 35 Notes Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
-
Page 36: Warranty & Repairs
Repaired parts or replacement products will be provided by Essex Electronics Inc. on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. Essex Electronics Inc. - Page 37 In no event shall Essex Electronics Inc. be liable for any damage to persons, property or area surrounding the installation site caused by any malfunction of the product manufac- tured by Essex Electronics Inc.
- Page 38 This Limited Lifetime Warranty shall be governed by and inter- preted in accordance with the California Uniform Commercial Code and by the procedural laws of the State of California. Any Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 39 All non-warranty repair freight charges are paid for by the customer. Non-warranty repair charges are returned COD. (Factory Authorized Distributors are subject to standard terms). Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...
- Page 40 Essex Electronics, Inc. | 805.684.7601 | 800.KEY-LESS | fax 805.684.0232 | keyless.com...