Python 1401 Owner's Manual page 43

R
The Bitwriter® [pin 99BUI
requires chip version 2.7 or
newer to progrom this unit.
Bitwriters with a dole code
01
60 or older require an IC
upgrade (pin 998MI. Some bitwriters with a dote code
of
68 do not require the IC upgrade, refer to tech tip #
1112 for more informotion
Startup Diagnostics: If the vehicle fails to activate the remote start, the remote stort
module will flash the parking lights on the vehicle to notify you
of
whot coused the
no-start situation.
See full Installation Guide for more
~
detail~d
inforr:nation on thiS system.
~~.
Such mformatlon and more can be
found online at: E L E e T RON I C 5
www.directechs.com
Note: If no remote pairing results, the system will exit after 60 seconds.
Parking Light Flashes
5 flashes Brake wire is active
6 flashes Hood pin wire is active
7 flashes Manual transmission mcde is enabled and not initialized.
B flashes Neutral safety wire hos no ground or the neutral safety switch is
Off.
Prepare the new remote to
be
Paired with the system
Remote Pair matches your l-way SuperCode remote to the system
1 Press and hold the
f
button for 8 seconds.
Note: The tronsmitLED will flash at 3 seconds. Please disregord and continue
10
hold
2. Wait for the Transmit LED to light solid. Release the
f
button.
3. Press the {:) for 1 second. The transmit LED will blink 3 times.
4.
Within 5 seconds, press the ~ button
5. The vehicle horn will honk, You have now successfully learned the remote to the
vehicle remote start system.
6 Press the
f
button tvvo times to exit learn routine on the remote. The transmit
LED will turn off and exit.
Remote Pairina
Prepare the vehicle system to be Paired with a new remote
1 Turn the key to the ON position.
2 Within 5 seconds press and release the Control bulton on the system's Control
Center one time.
3. Within 5 seconds, press and hold the Control button on the Control Center.
The status LED will flash one time ond the horn honks to confirm the vehicle is
reody for remote pairing. .
4. Release the Control button and proceed below
I' r~'
DATA TO DATA~"
Shutdown Mode
Runtime expired
Over-rev shutdown
Lowar no RPM
Transmitter shutdown (or optionol push button)
1+1 Broke shutdown
1-1
Hood shutdown
Timer mode/Turbo mode/Manual mode error·
Neutral safety shutdown
Low battery (voltage model
Wait-ta-start input timed out
To learn the tach signal:
1 Start the vehicle with the key.
2. Within 5 seconds, press and hold the Control button.
3 After 3 seconds the status LED on your Control Center lights constant when
the tach Signal is learned.
4 Release the Control button.
Learnina the Tach (not needed with Virtual Tachl
~.~
~
St a t u s
LED
Virtual Tach handles disengaging the starter motor during remote starting - it does
not address over-rev. If the customer wants to have the over-rev protection capability,
the tach wire must
be
connected.
Timer mode error: Ignition is on or shutdown input is active when activating
timer mode.
Turbo mode error: Turbo mode is programmed off, engine is not on or shut-
down input is active.
Manual mode error: MTS mode not enabled.
Installation Points
Remote Start Shutdown/Startuo Diaanostics
Important: Aher successfully learning Virtual Tach, a small minority of ve-
hicle storters may over crank or under crank during remote start. The Bit-
writer can be used fine tune the starter output time in 50mS increments to
compensate for such on occurrence.
Learning Virtual Tach (not needed with hardwire tach inputs)
Note: Virtual Tach cannot be used in MTS Manual Transmission Mode.
It
is also not
recommended for diesel trucks.
To program Virtual Tach:
1 After the install is complete, remote start the engine. The programming op-
eration may require 3 cranks
of
the starter before the engine starts and runs.
Do not turn off the remote start if this happens, it is a normal programming
operation
2. Once the engine begins running, let it run for at least 30 seconds
3. Using the Remote. send the Remote start command to turn remote start off.
Virtual Tach is programmed
To reset Virtual Tach, go into the Remote Pairing section
of
this gUide and press/re-
lease the Control button 4 times for step #4, then press and hold the Control button
to reset Virtual Tach. Virtual Tach cannot be reset with the Bitvvriter
To perform shutdown diagnostics:
1 With the ignition Off, press and hold the Control button.
2. Turn the ignition On and then back Off while holding the Control button.
3. Release the Control button.
4. Press and release the Control button. The status LED flashes to report the last
shutdown for one minute or until the ignition is turned on, as shown in the
folloWing table:
Status LED Flashes
I flash
2 flashes
3 flashes
4 flashes
5 flashes
6 flashes
lflashes
8 flashes
9 flashes
II flashes
(-) lOOmA 2ND STATUS /REAR DEFOGGER OUTPUT
(+) BRAKE SHUTDOWN INPUT
(-) NEUTRAL SAFETY INPUT
(-) 200mA STARTER OUTPUT
(-) HOOD PIN INPUT (NC OR NO)
(-) lOOmA IGNITION 1 OUTPUT
(-) 200mA FLEX RELAY CONTROL OUTPUT
(-) lOOmA STATUS OUTPUT
(-) 200mA ACCESSORY OUTPUT
PINK
DARK BLUE
GREY
ORANGE
PURPLE
BROWN
BLUEjWHITE
PINK/WHITE
BLACK/WHITE
Enhanced Tach Filtering
Addition
of
Aux 4 for a 10101
of
5 Channel Outputs
New 18 pin Harness
Improved current capable Aux
&
Factory Alarm Outputs
Enhanced Temperature Reading
~
Remote Start (H3) 8-pin connector
prr
t!ewle.atuwr... es'-- _
H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT
H3/2 REO/WHITE (+) FUSEO (30A) IGNITION 2 / FLEX RELAY INPUT 87
H3/3 ORANGE (+) ACCESSORY OUTPUT
H3/4, VIOLET (+) STARTER OUTPUT
'H3/S
RED (+) FUSED (30A) IGNITION 1 INPUT
H3/6 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT
H3/7 PINK/BLACK (+) FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY
H3/8 RED/BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT
(0) lOOmA AUX 4 OUTPUT
(0) lOOmA AUX 2 OUTPUT
(0) lOOmA FACTORY ALARM ARM OUTPUT
(-) lOOmA FACTORY ALARM DISARM OUTPUT
It'ooooooooo"ll
9 0 0 0 0 0 0 0 0 0 ,
(-) 200mA AUX 3 OUTPUT
(-) lOOmA AUX 1 OUTPUT
(-) DIESEL WAIT TO START INPUT
TACHOMETER INPUT
EMPTY
SOOmA (-) LOCK OUTPUT
NOT USED
VIOLETjWHITE
WHITEjVIOLET
ORANGE/BLACK
VIOLET/BLACK
LIGHT GREEN/BLACK
WHITE/BLACK
GREY/BLACK
GREEN/WHITE
HZ/8
HZ/6
HZ/4-
HZ/l
HZ/3
HZ/9 "
Hl/8
'I
GREEN
I (-)
DOOR TRIGGER INPUT (N/C" N/O)
HZ/Z
Hl/S
I
BlACK
I (-)
CHASSIS GROUND
HZ/S
Htj4
1
WHITE/BROWN
I
LIGHT FLASH ISOLATION WIRE - PIN 87a of onboard relay
H1/6
!
VIOLET
I
(+) DOOR TRIGGER INPUT
HZ/7
H1/2
I
RED
I
(+)12VDC CONSTANT INPUT
Hl/1
I
RED/WHITE
I (-)
200mA TRUNK RELEASE OUTPUT
H1/3
I
BROWN
I (-)
lOOmA HORN HONK OUTPUT
Hl/9
I
BLACKfWHITE
I (-)
lOOmA DOME LIGHT OUTPUT
H1{7.
I
BLUE
I
FACTORY HORN INPUT (Use jumper to set polarity)
Hl/10'1 WHITE/BlUE
I (-)
REMOTE STARTI TURBO TIMER ACTIVATION INPUT
~1/11
I
WHITE
I
PARKING LIGHT OUTPUT
H1/12
I
ORANGE
I (-)
SOOmA GROUND WHEN ARMED OUTPUT
Quick Reference Install Guide
Remote Start
wi
Keyless Entry
1-Way
H2 Harness, l8-pin connector
i
,~y~~~~;,~~~~~"~IL~~'~~ed~~~Y
i
~- ~N;e~ut!"1IlSa~fe"ty~~;:~;;;~::~~J[:~:::r~
and mtheON position
,~
Switch
~
,--------------------------- --~
Control Center
Door Lock, 3-pin connector
lBl
I
i
SOOmA (_) UNLOCK OUTPUT
i
i -
Main Harness (Hl), 12-pin connector II:
0 0 0 0 0 0 0 0 0 0
,~II
o 2009 Directed Ele<t,onies, All rigntsReserved
Wiring Connections