Table of Contents
Advertisement
• When using the optional stay
!"#
•
•
Fire wall
Washer
Dashboard
Sleeve
Removing the unit
• Before removing the unit, release the rear
section.
1
Remove the control panel.
2
Remove the trim plate.
3
Insert the 2 handles into the slots, as shown.
Then, while gently pulling the handles away
from each other, slide out the unit. (Be sure
to keep the handles after installing it.)
1
Control panel
!
Parts list for installation and connection
The following parts are provided with this unit.
After checking them, please set them correctly.
Hard case/Control panel
!"#$
Power cord
!"#$%&
(Power Cord)
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you
disconnect the battery's negative terminal and make
all electrical connections before installing the unit. If
you are not sure how to install this unit correctly, have
it installed by a qualified technician.
Note:
This unit is designed to operate on 12 V DC, NEGATIVE
ground electrical systems. If your vehicle does not
have this system, a voltage inverter is required, which
can be purchased at JVC car audio dealers.
• Replace the fuse with one of the specified rating. If
the fuse blows frequently, consult your JVC car
audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power
circuit. However, with some vehicles, clicking or
other unwanted noise may occur. If this happens,
connect the unit's rear ground terminal (see
connection diagram) to the car's chassis using
shorter and thicker cords, such as copper braiding
or gauge wire. If noise still persists, consult your
JVC car audio dealer.
• Maximum input of the speakers should be no more
than 45 W at the rear and 45 W at the front, with an
impedance of 4 Ω to 8 Ω.
• Be sure to ground this unit to the car's chassis.
• The heat sink becomes very hot after use. Be careful
not to touch it when removing this unit.
Heat sink
•
Stay (option)
!"
Lock nut
!
Screw (option)
!"
Mounting bolt
!
!
!
!"#$%&!"'()*+,-.(/
•
1
!"#$
2
!"#
3
!"#$%&'()*+,-."/
!"#$%&'#()*+,-./
!"#$%&'()*+,-.
2
Trim plate
!"#$%&'(
!"#$%&'()
!"#$%&'()*
Sleeve
!
Handles
Rubber cushion
!"
!
!"#$%&'()*+,#-./01
!"#$%&'()*+,-./012
!"#$%&'()*+,-./01#
!"#$% 12V
!"#$%&'()*+,-./'0(
!"#$% JVC
!"#$%&'()*
•
!"#$% JVC
!"#$
•
!"#$%&'()*+,-./0 1
!"#$%&&'()*+,-./01
!"#$%&'()*+,-./0(1
!"# $%&'( )*+
!"#$%&
!"#$%&'
JVC
!"#$%&'()*+,%- 45
•
!"#$%&'45
!"#$%&'()
•
!"#$%&'(%)*+#,-.
•
!"#$%&'()
• When installing the unit without using the sleeve
!"#$%&'($
•
•
In a Toyota for example, first remove the car radio and install the unit in its place.
! TOYOTA
!"#$%&
Flat type screws (M5 x 6 mm)*
!
(M5 x 6 mm)*
*
(M5 x 6
)
*
x
M5
Bracket*
Pocket
*
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are
used, they could damage the unit.
!"#$%&'()*+,
•
1
2
3
2
Trim plate
Washer (ø5)
!"
=(ø5)
(ø5)
!"#$%&'
!"#$%&'(
!+,-
!"#$%&'
!"
!"#$%&'()
!"#$4 – 8
45
4
•
'()*+,-.)/012&3456
*
*
Bracket*
*
*
*
!"#$%&'
!"()*+,-#
6mm
6
3
Handle
Lock nut (M5)
!=(M5)
(M5)
M5
Mounting bolt (M5 x 20 mm)
!=(M5 x 20 mm)
(M5 x 20
)
x
M5
12
JVC
JVC
(Power Circuit)
JVC
45
8
* Not included with this unit.
!"#$
*
*
*
Flat type screws (M5 x 6 mm)*
!
(M5 x 6 mm)*
*
(M5 x 6
)
*
x
M5
•
!"
Only for KS-FX711
KS-FX711
KS-FX711
Remote controller
!
Battery
CR2025
DC
JVC
•
JVC
•
JVC
•
•
•
Advertisement
Table of Contents
