Advertisement
Page 6
I
NSTALLING
• Mount the bracket to Chili before installing on the piano. It is important that the
shoulder washers have the same orientation as shown above.
• Place the unit under the front of the piano in a pulled out position.
• Use a screw gun to insert the rear screws.
• Pull the unit back all the way giving you access to the holes in the front of the
mounting bracket.
• Screw in the front 2 screws. Be sure they are fully inserted or you will scratch the
top of the unit.
U
T
P
PDATING
HE
If you are upgrading from a previous version of Pianomation MIDI you will need to update the EPROM to version
1.51 or 1.61 . The version 1.51 EPROM requires a 256 processor, similar to the one shown below, and their
associated cables. Below are the QRS part numbers required. The EPROM version is written on the chip which is
located on the processor board.
Description
EPROM 1.51
P LA Y . A S M © 1993
P i a no A ut omat i o n
V er 1. 30 S N : ****
EPROM version 1.50 is required in an existing piano.
This goes into the processor located under the piano.
PLAY.ASM ©1993
Piano Automation
Ver 1.30 SN: ****
1.51K
QRS Processor
Test & Alignment
User Control Cable
Note Driver Signal Cable
Power Supply Cable
Cat. No. 60100
Cat. No. 811435
Cat. No. 70329
Cat. No. 70319
Cat. No. 811434
Status
Note: If Chili is mounted on the piano flip dip switch 3 up. Dip switches are located on the side of the Year 2000
processor and inside the enclosure on the previous years enclosures.
Owners Manual
O
Y
P
N
OUR
IANO
Be sure any powered speakers
plugged into Pianomation MIDI
are plugged into the
Pianomation system power
supply's switched outlet.
E
IANOMATION
NGINE
QRS Part Number
70570
To Driver Boards
To Power Supply
To User Interface
To Test Box
MIDI In
Year 2000 Release
For Technical Support Call 1-941-597-5888
•
The Yamaha concert
Yamaha does not always adhere to the General MIDI specification
series floppy does not
when asking for specific instruments. This may cause the sounds
sound right.
out of the Chili unit to play differently.
•
Some piano keys are
When this is noticeable give your technician a call, or give QRS a
playing louder than
call, there are routines built into Chili to adjust for this but some
others, or the sustain
instruction is necessary. This setup is typically done after a tuning
pedal does not have
or when initially installed in the home.
enough power to
energize our system.
•
The sustain event is not
The sustain switch must be accurately installed or it will effect the
recorded accurately.
entire performance. The sustain switch is located either under the
piano or inside the piano. If it is inside the piano call your
technician to come adjust it. If it is still not to your satisfaction do
not let them leave without calling us first.
•
The speaker on the piano
This occurred on most of the first units built that did not have the
Pops when I turn the unit
powered speaker plugged into the switched power supply of the
on.
Pianomation MIDI system and version 1.51k EPROM is not
installed.
•
My disk is not recognized
Make sure you used a clean formatted floppy and make sure the
when I upgrade.
name of the file is QRSUpdat.bin.
•
The Metronome does not
Check to make sure you are getting MIDI out from your record strip.
•
stop when I start
Check the record strips power.
•
recording.
Select MIDI as your source, choose an instrument, play the piano, if
you hear the instrument out of the speaker then the record strip is
working. Go back to record, record, stop and play. If it still does
not record. Call QRS.
•
The unit does not power
This usually occurs when the system is writing to flash. Hold clear
down.
for two seconds, this will interrupt what it is doing and shut down.
Page 63
N
OTES
Advertisement
