Download Print this page

Advertisement

Operator's manual
DM 230
Please read the operator's manual carefully and make sure you understand the
instructions before using the machine.
EN, CN

Advertisement

   Related Manuals for Husqvarna DM 230

   Summary of Contents for Husqvarna DM 230

  • Page 1

    Operator’s manual DM 230 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. EN, CN...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: WARNING! The machine can be a Inspection and/or maintenance should dangerous tool if used incorrectly or be carried out with the motor switched carelessly, which can cause serious or fatal off and the plug disconnected.

  • Page 3: Table Of Contents

    SAFETY INSTRUCTIONS General safety warnings ..........General working instructions ........Machine′s safety equipment ........Checking, maintaining and servicing the machine′s safety equipment ............PRESENTATION DM 230 ................ STARTING AND STOPPING Before starting ............. Starting ................ Stopping ............... MAINTENANCE General ................

  • Page 4: What Is What

    WHAT IS WHAT? What is what on the drilling machine? 1 Drill spindle 9 Gear knob 2 Water connector 10 Leakage hole (if water or oil trickles out from the leakage hole contact your dealer to replace the seals) 3 Gearbox and motor module 11 Stiffener 4 Smart Start®...

  • Page 5: Safety Instructions

    • Heavy-duty, firm grip gloves. your machine both efficiently and safely. Let your Husqvarna dealer check the drilling machine regularly and make essential adjustments and repairs. Husqvarna Construction Products has a policy of continuous product development. Husqvarna reserves the right to modify the design and appearance of products without prior notice •...

  • Page 6: Safety Instructions

    SAFETY INSTRUCTIONS General safety warnings • If operating a power tool in a damp location is unaviodable, use a ground fault circuit interrupter protected supply. Use of an GFCI reduces the risk of electric shock. WARNING! Read all safety warnings and all instructions.

  • Page 7: General Working Instructions

    SAFETY INSTRUCTIONS • Never work alone, always ensure there is another person • Do not overload the machine. Overloading can damage close at hand. Apart from being able to receive help to the machine. assemble the machine, you can also get help if an •...

  • Page 8: Machine's Safety Equipment

    SAFETY INSTRUCTIONS Machine′ ′ ′ ′ s safety equipment Stand drilling • Always use a drilling stand if drilling is to be performed This section describes the machine′s safety equipment, its from a ladder or scaffold. purpose, and how checks and maintenance should be carried out to ensure that it operates correctly.

  • Page 9: Checking, Maintaining And Servicing The Machine's Safety Equipment

    SAFETY INSTRUCTIONS Ground fault circuit interrupter Check the ground fault circuit interrupter Ground fault circuit interrupters are for protection in case an Connect the machine to the socket. Push the RESET button electrical fault should occur. (green) and the red LED lights up. The LED indicates that the ground fault circuit interrupter is on and that the machine can be switched on.

  • Page 10: Presentation

    The DM 230 is an electric handheld drill, intended for drilling concrete, brick and various stone materials. The soft rear section on the DM 230 has a large contact area • The drilling machine has a modular design and is easy to so that the machine sits better against the body.

  • Page 11: Starting And Stopping

    STARTING AND STOPPING Before starting 2 Turn on the water cooling (wet drilling) or switch on the vacuum cleaner (dry drilling). WARNING! Note the following before starting: The machine should be connected to an earthed outlet socket. Check that the mains voltage corresponds 3 Hold the machine steady.

  • Page 12: Maintenance

    MAINTENANCE General • In order for the machine to always be cooled sufficiently the cooling air openings must be kept clear and clean. Blow down the machine regularly with compressed air. WARNING! Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected.

  • Page 13: Replacing The Carbon Brushes

    MAINTENANCE 3 Unscrew the six screws holding the motor - gearbox 4 Pull the carbon brush out from the holder. modules together. 4 Carefully disassemble the machine. 5 Clean the brush holder with compressed air or a brush. 5 Empty the gearbox oil into the container. Replace the brush if worn.

  • Page 14: Technical Data

    TECHNICAL DATA DM 230 Electric motor Single-phase Rated voltage, V 220-240/100-120 Rated output, W 1850 Rated current, A 220-240 V 100-120 V 15 A Weight, kg Diameter drill bit, mm Max. diameter of the drill bit, with stand 150 mm (5,9”) Max.

  • Page 15: Ec-declaration Of Conformity

    (Applies to Europe only) Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna 230, from 2010´s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), conforms with the requirements of the COUNCIL’S DIRECTIVE:...

  • Page 16

    – Chinese...

  • Page 17

    Chinese –...

  • Page 18

    – Chinese...

  • Page 19

    Chinese –...

  • Page 20

    – Chinese...

  • Page 21

    Chinese –...

  • Page 22

    – Chinese...

  • Page 23

    Chinese –...

  • Page 24

    Softstart™ DM 230 ™ Smartstart™ ™ ™ Elgard™ ™ – Chinese...

  • Page 25

    Chinese –...

  • Page 26

    – Chinese...

  • Page 27

    Chinese –...

  • Page 28

    DM 230 Ø – Chinese...

  • Page 29: Wiring Diagram

    WIRING DIAGRAM Chinese –...

  • Page 32

    EN – Original instructions CN – ´®z+V9-¶8s¨ ´®z+V9-¶8s¨ 1154251-38 2012-06-20...

Comments to this Manuals

Symbols: 0
Latest comments: