Table of Contents
Advertisement
9.
Light the burner pilots. See Step
15, Page 6. Adjust the pilot flame as
shown in Step 15b. NOTE: This must be
done after conversion is completed.
10.
Light the oven burner pilot.
11.
Install control knobs. Check for
proper flame. The cooktop burner flames
should have a small inner cone with a
very distinct blue flame 1/4" to 1/2" long.
The outer cone is not as distinct as the
inner cone. The oven burner flame
should be 1/2" long with a bluish-green
inner cone and dark blue outer mantle.
L.P. gas flames have a slightly yellow tip.
If the flames are noisy or blowing, they
are getting too much air. If the flames are
soft and lazy, they are not getting enough
air. If burners need adjusting, see "Check
operation" section, Steps 18-23, Page 7.
12.
Close broiler door. Turn oven
control knob to "OFF" .
13.
Remove control knobs.
Reinstall the control panel. Securely
tighten the 4 screws. Reinstall the control
knobs. ( The oven control is the center
knob.)
Important: If not done in Step 9, check
the "LO" flame adjustment. See "Check
operation" section, Step 20, Page 7.
Natural gas
conversion
1.
Check that the manual shutoff valve
in the gas supply line has been turned off.
2.
Open broiler drawer and remove
broiler pan. The pressure regulator is
located in the back right hand corner of
the broiler compartment.
DO NOT REMOVE THE PRESSURE
REGULATOR.
3.
Pressure
regulator: Remove
the cap from the
pressure regulator.
Turn the cap over so
that N or NAT is
visible. Replace the cap.
4.
Remove burner grates, burners
and screws. Lift cooktop. NOTE: There is
no cooktop support rod.
5.
Cooktop burners:
a.
Check that all control knobs are in the
OFF position and remove the knobs.
b.
Remove the control panel. (See Step
18a, Page 7.)
c.
Remove the
screws holding
burner tube
assemblies to
bracket and
carefully move
tubes back away
from orifice.
viewed from
inside broiler
compartment
burner
screw
orifice
tube
screws
assemblies
Remove and replace
orifice spuds.
orifice spuds
notches
NAT
L.P .
Note: Burner tube and
gas
brackets not shown.
manifold
"145"
"145"
L.R.
L.F.
d.
Locate Natural gas orifice spuds for
top burners in literature package
included with the range. Natural gas
spuds are stamped "145" . Remove
Natural gas orifice spuds using a 3/8"
combination wrench. Install Natural gas
orifice spuds to replace the L.P. gas
orifice spuds.
Place L.P. gas orifice spuds in plastic parts
bag for future use and keep with literature
package.
Reinstall burner tube assemblies and
tighten screws securely.
e.
Lower cooktop. Reinstall screws to
secure burner tube assemblies to
cooktop and tighten securely. Reinstall
burners and burner grates.
Do not reinstall control panel or knobs.
They will be reinstalled at Step 11, on
Page 10 .
Natural gas oven
orifice spud stamped
with "47"
6.
Oven burner:
a.
Carefully pull oven burner away from
back wall of oven just enough to access
the orifice spud located behind the
burner's air shutter.
b.
Locate Natural gas orifice spud
stamped "47" in literature package
supplied with range.
"145"
"145"
R.R.
R.F.
oven burner
orifice behind
air shutter
9
Advertisement
Table of Contents
