Dimplex PCH2000TCW Installation Instructions page 3

Figure 3
A
D
C
B
A - Setting/Temperature Display
B - Comfort Setting Icon
C - Economy Setting Icon
D - Set Back Temperature Setting
E - Synchronized Icon
F - Lock Icon
G - Decrease Button
H - Increase Button
I - Menu Button
!
NOTE: Either the or
dependent on the setting being used.
C. Economy Setting
The Economy Setting can be used to change the Setpoint
Temperature for a user determined period of time. By
pressing the V the Economy Setting will be enabled -
signified by the icon flashing. After the Set Back Temperature
has been set, the icon will become solid after three seconds
and the Set Back Temperature will be enabled.
To return back to the Comfort Setting press the V button. The
icon will disappear and the
D. Set Back Temperature Setting
The Set Back Temperature Setting is used during periods
when the Economy setting feature is active. This temperature
adjustment can be set by pressing the V followed by the ✚
or –.
E. Synchronized Icon
The PCH features CONNEX
works with Dimplex single and multi-zone CONNEX
controllers to provide simple whole home connectivity and
comfort. CONNEX controllers are available to control one
TM
or multiple Precision Comfort Heaters within a 50' (15 m)
radius. In order for the controller to have this function the
PCH and the controller will need to be synchronized. To do
this:
1. On the PCH heater press and hold the V button for 3
seconds, both the
2. Press the – , ✚ and then V, on the PCH heater.
3. Within 10 seconds press any button once on the
CONNEX Controller.
TM
!
NOTE: There is a 3 second delay between pressing the
last button on the controller and the PCH heater.
!
NOTE: To desynchronize a PCH heater from the
synchronized CONNEX
TM
heater or the controller:
1. Press and hold the V for 3 seconds.
2. Press the V, ✚ and then –.
F
E
icon will always be visible,
icon will appear.
, a wireless technology that
TM
and icons will begin to flash.
Controller; on either the PCH
Nothing will need to be done to the other component.
Dimplex single and multi-zone CONNEX
sold separately and are available for purchase from your
authorized Dimplex dealer.
To find your local Dimplex dealer, visit www.dimplex.com.
H
F. Lock Icon
G
The PCH has a Lock feature to prevent settings from
I
accidentally being changed.
1. Press and hold the V for 3 seconds. Both the
Icons will begin to flash.
2. To Enable: Within 5 seconds press ✚, then –, then ✚,
then –. The
To Disable: Within 5 seconds press –, then ✚, then –,
then ✚. The
!
NOTE: The PCH can be locked in either the Comfort or
Economy Setting. Ensure that the desired icons are present
when locking is complete.
Boost Function
The PCH is also equipped with a "Boost Function"
which allows the user to run the unit at full heat, for a
predetermined amount of time, to quickly heat up a cold
room/space. The Boost can be set for a maximum of 20
minutes, in 5 minute increments.
To enable Boost:
1. Press and hold ✚ for 5 seconds. The area where the
temperature normally displays will begin to toggle
between the display of "HI" and "20".
!
NOTE: The "20" indicates the time (in minutes) remaining
in Boost function. The timer is updated as the time counts
down 19, 18, 17, etc.
2. The length of time that Boost is enabled for can be
adjusted by pressing the ✚ or – buttons. Every time the
✚ or – button is pressed the timer will be adjusted by 5
minutes and will cycle back to 20 minutes.
3. When the timer times out the heater will return to the
programmed settings.
TM
!
NOTE: At any time you can hold down the – button for 5
seconds and exit the Boost function.
controllers are
TM
icon will appear
icon will disappear.
and
3