Page 2
Copyright 2008, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
Page 5
Diamond Digital is a registered trademark of Mitsubishi Electric Australia Pty. Ltd. Microsoft and Windows are registered trademarks of Microsoft Corporation.
CHAPTER 1 INTRODUCTION Thank you for choosing the Diamond Digital DX-D191P LCD monitor. Your LCD monitor is safe to use and completely free from any X-ray radiation. We hope you enjoy using our product, and would like to provide the following additional information to assist you in obtaining the best results, using the product safely and in complete comfort.
1.3 Package Contents Standard package includes the following: 1. 19" TFT LCD Monitor. (Depend on the screen diagonal) 2. Power Adapter. 3. User Manual. 1.4 Product Care 1. To remove dust or dirt from the screen, use a soft clean cotton cloth and wipe gently.
1.6 Caution PRODUCT ● 1. Do not cover or block the ventilation holes in the back of the monitor case. 2. Do not insert any metal objects into the ventilation holes of the monitor case and be careful not to spill liquids over this product as this could result in severe injury.
Page 9
If the monitor housing is damaged or broken. POWER CORD AND SIGNAL CABLE ● 1. Do not place anything on the power cord or signal cable. 2. Do not allow any cables from the monitor to lie on the floor in an area where pedestrians are likely to trip, causing injury.
CHAPTER 2 OPERATION INSTRUCTIONS 2.1 Front Control Panel 1. Power Switch: press to switch monitor on / off. 2. LED Indicator: power indicator. 3. Mode: press to select input signal. (See ※ Note) 4. Plus (+): press to increase the value of OSD option selected 5.
2.3 OSD Function Table VIDEO (BNC Composite) ● Colour Adjust the colour density. Tint Adjust the colour tint. (NTSC only) Brightness Adjust back ground black level of the screen image. Contrast Adjust fore ground white level of the screen image. Sharpness Adjust the clarity and focus of the screen image.
CHAPTER 3 SIGNAL CONNECTOR AND INSTRUCTION Input / Output Interface 1. DC In 2. DC Out: DC 12V / MAX. 1A. 3. VIDEO In / Out (BNC-TYPE) If you choose a video input without connecting any video signal, “No Signal" will be displayed onto the screen.
CHAPTER 4 VIEWING ANGLE For the user’s convenience, the LCD screen may be tilted according to viewing requirements. The monitor can be tilted forward up to 5 degrees or backward up to 40 degrees.
Page 16
WB-191 - WALL MOUNTING BRACKET 【OPTIONAL】 ● ● Base Dismounting Process (Step 1) Remove the Hinge Cover (1-1) Insert a thin tool into the hole of the hinge cover, then pull upward and outward to remove the cover. . (1-2) Pull the cover outward 4~5 mm as indicated by arrow A, then pull the cover upward as indicated by arrow B, then remove the cover.
CHAPTER 5 PANEL SPECIFICATION Please refer to attach specification sheet. MODEL 19" Pixel pitch 0.294 x 0.294. (H x V mm) VGA / DVI 1280 x 1024 pixels. Max. Resolution VIDEO 500TVL. Dimension 421.2 x 405.6 x 170.0 (W x H x D mm) Packing Dimension 553.0 x 534.0 x 242.0 (W x H x D mm)
CHAPTER 6 WARRANTY After Sales Service After this product is unpacked, keep the carton and packing materials to ensure safe transportation in case of any after sales service. The warranty is covered by a 3 year limited warranty, subject to normal conditions of use.
Service Contacts Australian Service Contacts Visit the Customer Support page of Mitsubishi Electric Australia’s web site at; www.mitsubishielectric.com.au Further details of your nearest Mitsubishi Electric Authorized Service Center or to contact a Mitsubishi Electric Service Representative in your state or territory: New South Wales and Australian Capital Territory 348 Victoria Road Rydalmere, NSW, 2116...
Page 20
South Australia and Northern Territory 77 Port Road Hindmarsh, SA, 5007 Telephone: (08) 8340-0444 Fax: (08) 8340-0555 Victoria and Tasmania Building 28 Omnico Business Park 270 Ferntree Gully Rd Notting Hill, VIC, 3168 Telephone: (03) 9535-7800 Fax: (03) 9535 7801 Western Australia 5 / 329 Collier Road Bassendean, WA, 6054...
Need help?
Do you have a question about the DX-DI92 and is the answer not in the manual?
Questions and answers