Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Diamond Digital DV150J
Summary of Contents for Diamond Digital DV150J
- Page 1 Diamond Digital DV150J/JB Colour TFT LCD Monitor 15” (38 cm) LCD Panel Size...
- Page 2 Copyright 2005, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
-
Page 3: Table Of Contents
Table of Contents Important Safety Instructions ..........1 Features................2 3 Unpacking the Monitor .............3 4 Hardware Installation ............5 5 Windows driver installation ..........8 6 Setting the Display Resolution ........9 Choosing the Best Resolution...........9 Supported Graphics Modes and Refresh Rate Selection 10 7 Adjusting the Monitor.............13 User Controls ..............13 Adjusting the Monitor's Display ........14... - Page 4 Diamond Digital is a registered trademark of Mitsubishi Electric Australia Pty. Ltd. Microsoft and Windows are registered trademarks of Microsoft Corporation.
-
Page 5: Important Safety Instructions
Important Safety Instructions Please read the following safety instructions before installing or cleaning your Diamond Digital monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. -
Page 6: Features
(typical) ♦ High Contrast Ratio – 450:1 (typical) ♦ True Colour Display With 16.2M (6bit + FRC) colour, the DV150J/JB monitor offers you better image quality. ♦ High Quality Ratiometric Expansion With any resolution within the monitor’s specified range, your Diamond Digital DV150J/JB monitor can expand the image to full screen. -
Page 7: Unpacking The Monitor
Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately LCD monitor User’s Manual VGA Cable Power Cord... - Page 8 Locate the model name and the serial number label on the back of your monitor, and write the details of the monitor and your place of purchase in the space on page (ii) of this manual for future reference.
-
Page 9: Hardware Installation
Hardware Installation Connecting the Monitor Base Remove the base from the packing box and place it on the desk. Next, remove the LCD display and carefully seat it on the base. (See fig.1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to adjust the viewing angle. - Page 10 Connecting the Display to your Computer Using the VGA cable Power off your computer. Connect one end of the VGA signal cable to the LCD Monitor’s VGA port. (See Fig 1-3) Connect the other end of the signal cable to the VGA port on your PC. Make sure connections are secure.
- Page 11 Instructions for VESA Mounting To detach the LCD Monitor from its stand, unscrew the two screws for the monitor stand and pull it downwards to remove, then unscrew the two screws for the monitor stand bracket and pull this down to remove. Figure 1-6 Interface for Arm Applications Before installing the mounting device, please...
-
Page 12: Windows Driver Installation
Windows driver Installation The DV150J/JB is fully Windows Plug and Play compatible so no specific Windows drivers are required for installation. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add New Hardware wizard. -
Page 13: Setting The Display Resolution
LCD. In the case of the DV150J/JB the LCD resolution is 1024 x 768 pixels. This is also known as the “native” resolution of the monitor. Lower resolutions can be displayed at full screen through an interpolation circuit. -
Page 14: Supported Graphics Modes And Refresh Rate Selection
Table 1 on the next page. Other graphics signals may be displayed poorly or not at all. Note that the DV150J/JB’s preset modes correspond to VESA or Apple Macintosh standard graphics signals for these resolutions. All recent models of graphics adaptors... - Page 15 should be able to support these modes. For the native resolution of 1024 x 768 pixels, for example, refresh rates of 60, 70 and 75 Hertz are supported. With Windows 95, 98, ME, 2000 or XP you can change the refresh rate of the graphics signal as follows: 1.
- Page 16 Table 1 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. H. Freq. V. Freq. Pixel Freq. H/V Sync. Resolution Mode (KHz) (Hz) (MHz) Polarity 640 x 350 31.469 70.087 25.175...
-
Page 17: Adjusting The Monitor
Adjusting the Monitor User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 Stereo Speakers PC Audio Stereo output. Speaker Volume Increase Volume - Turn knob clockwise. Control Decrease Volume - Turn knob counter clockwise DC Power Switch Press the power switch to switch the monitor ON/OFF. -
Page 18: Adjusting The Monitor's Display
Adjusting the Monitor's Display OSD Function Menu To access the OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. 2-2. Continue pressing the Function Select buttons to scroll through the available menu items, then press the Adjustment Control buttons to adjust the setting Figure 2-2... - Page 19 Icon Function Description Sets the CIE coordinate color 9300 CIE coordinated Color Temperature of 9300°K temperature to 9300°K Sets the CIE coordinate color 6500 CIE coordinated Color Temperature of 6500°K temperature to 6500°K Three colors (Red, Green, Blue) can be adjusted Sets the settings to a by user defined User from the OSD menu...
- Page 20 surrounding text and icons, for any movement or change. Adjust the Clock setting and see how this affects this “noise” or movement. Make sure that in correcting noise in one part of the screen the setting does not create it in another.
-
Page 21: Frequently Asked Questions
Frequently Asked Questions The image is blurred, how can I get the best quality picture? Read chapter 6, Setting the Display Resolution, and select a graphics ♦ signal with the correct resolution and refresh rate. Then read chapter 7, Adjusting the Monitor, and make adjustments to the displayed image based on these instructions. - Page 22 No image is displayed, what can I do? Check that the light (LED) next to the monitor’s power button is lit and is ♦ green in colour. If the LED is green, press one of the Function Select buttons on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Setting the Display Resolution and reset the graphics card to one of the monitor’s supported graphics signals.
-
Page 23: Specifications
Specifications Diamond Digital DV150J/JB Model: Display Characteristics Display Type 15“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 38 cm / 15” Native (Maximum) Resolution 1024 x 768 pixels Colours 16.2 million (6 bit + FRC) Contrast Ratio... - Page 24 Input Signal Line Frequency 24 – 61kHz multi-frequency Image Frequency (Refresh Rate) 56 - 75Hz Video Signal RGB analogue (Positive polarity) 0.7 Vpp/75 Ohm Synchronization Separate TTL, composite TTL Signal Connection 15-pin mini D-sub Physical Characteristics Power Management VESA DPMS, Energy Star Maximum Power Consumption 30 Watts Power Saving Mode...
-
Page 25: Service Contacts
Service Contacts If problems remain after checking this manual, please contact your place of purchase or contact: Australian Service Contacts Visit the Customer Support section of Mitsubishi Electric Australia’s web site at www.mitsubishielectric.com.au for details of your nearest Mitsubishi Electric Authorized Service Center or contact the Service Department for your state: New South Wales and Australian Capital Territory 348 Victoria Road... - Page 26 Victoria and Tasmania 4 / 303 Burwood Hwy East Burwood, VIC, 3151 Telephone: (03) 9262-9899 Fax: (03) 9262-9850 Western Australia 5 / 329 Collier Road Bassendean, WA, 6054 Telephone: (08) 9377-3411 Fax: (08) 9377-3499 New Zealand Contact: BDT New Zealand Ltd. 1 Parliament St.
Need help?
Do you have a question about the DV150J and is the answer not in the manual?
Questions and answers