DeWalt D25012 Instruction Manual

DeWalt D25012 Instruction Manual

Heavy-duty sds plus rotary hammers
Hide thumbs Also See for D25012:

Advertisement

D25012
D25013
www.
.eu

Advertisement

Table of Contents
loading

Summary of Contents for DeWalt D25012

  • Page 1 D25012 D25013 www.
  • Page 2 Figure 1 D25013 D25012 Figure 2 D25013...
  • Page 3 Figure 3 Figure 4...
  • Page 4: Technical Data

    EN GL IS H HEAVY-DUTY SDS PLUS ROTARY HAMMERS ® D25012, D25013 Chiselling Congratulations! Vibration emission You have chosen a D WALT tool. Years of value a m/s² – experience, thorough product development and h,Cheq Uncertainty K = m/s² –...
  • Page 5: Ec Declaration Of Conformity

    Keep children and bystanders away while operating a power tool. Distractions can D25012, D25013 cause you to lose control. WALT declares that these products described 2) ELECTRICAL SAFETY under “technical data” are in compliance with: Power tool plugs must match the outlet.
  • Page 6 EN GL IS H 3) PERSONAL SAFETY Store idle power tools out of the reach Stay alert, watch what you are doing and of children and do not allow persons use common sense when operating a unfamiliar with the power tool or these power tool.
  • Page 7: Residual Risks

    EN GLI SH • Keep a firm grip on the tool at all times. Markings on Tool Do not attempt to operate this tool The following pictograms are shown on the tool: without holding it with both hands. It is recommended that the side handle be used at Read instruction manual all times.
  • Page 8: Electrical Safety

    EN GL IS H h. Reversing lever The minimum conductor size is 1.5 mm i. Lock-on button When using a cable reel, always unwind the cable completely. j. Depth rod release button INTENDED USE ASSEMBLY AND ADJUSTMENTS These heavy-duty rotary hammers have been WARNING: To reduce the risk of designed for professional drilling and hammerdrilling, injury, turn unit off and disconnect...
  • Page 9: Operation

    EN GLI SH Mode Selector (fi g. 1, 2) WARNING: Burn Hazard. ALWAYS wear gloves when changing bits. NOTICE: Tool must come to a Accessible metal parts on the tool complete stop before activating the and bits may get extremely hot during mode selector button or damage to the operation.
  • Page 10: Overload Clutch

    EN GL IS H NOTE: Use lower speeds for starting holes without Drilling (fi g. 2) a centerpunch, drilling in metal, plastics or ceramics, WARNING: To reduce the risk or driving screws. Higher speeds are better for of serious personal injury, turn drilling in masonry for maximum efficiency.
  • Page 11: Maintenance

    EN GLI SH 5. To minimize stalling or breaking through the Hammerdrill Operation material, reduce pressure on drill and ease the 1. When drilling, use just enough force on the bit through the last fractional part of the hole. hammer to keep it from bouncing excessively 6.
  • Page 12: Motor Brushes

    EN GL IS H WARNING: To reduce the risk of Optional Accessories injury, turn unit off and disconnect WARNING: Since accessories, other machine from power source before than those offered by D WALT, have installing and removing accessories, not been tested with this product, use before adjusting or changing set-ups of such accessories with this tool could or when making repairs.
  • Page 13 EN GLI SH GUARANTEE WALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user.
  • Page 14 Black & Decker - D WALT Tel: +32 (0)015 - 15 47 9211 België en Luxemburg Nieuwlandlaan 7, IZ Aarschot B156 Fax: +32 (0)015 - 15 47 9210 B-3200 Aarschot www.dewalt.be Danmark WALT Tlf: 70201511 Sluseholmen 2-4 Fax: 70224910 2450 København SV www.dewalt.dk...

Table of Contents