Sherwood Newcastle A-965 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Sherwood Manuals
  4. Amplifier
  5. Newcastle A-965
  6. Operating instructions manual

Sherwood Newcastle A-965 Operating Instructions Manual

7-ch power amplifier
Hide thumbs Also See for Newcastle A-965:

Advertisement

Table of Contents

A - 965
7-CH Power Amplifier

Advertisement

Table of Contents
loading

Related Manuals for Sherwood Newcastle A-965

Summary of Contents for Sherwood Newcastle A-965

  • Page 1 A - 965 7-CH Power Amplifier...

  • Page 2: Introduction

    Introduction READ THIS BEFORE OPERATING YOUR UNIT CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

  • Page 3: Safety Instruction

    1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

  • Page 4: Table Of Contents

    CONTENTS Introduction READ THIS BEFORE OPERATING YOUR UNIT System Connections VARIOUS CONNECTIONS OF SPEAKER CORDS SPEAKER PLACEMENT Front Panel Controls Operations Troubleshooting Guide Specifications | 11 | 10...

  • Page 5: System Connections

    • Make connections firmly and correctly. If not, poor connections can cause loss of sound, noise or damage to the unit. • For connections between this unit and the Sherwood compatible pre amplifier such as P-965, refer to the system connections in the operating instructions of that.
  • Page 6 • Only when enjoying either 6.1 or 7.1 channel surround playback, connect either the surround back left speaker only or both of surround back speakers. • To emphasize the deep bass sounds, connect a powered subwoofer to the pre amplifier such as Sherwood P-965 not to this power amplifier. (For details, refer to the operating instructions of the pre amplifier.) •...

  • Page 7: Various Connections Of Speaker Cords

    VARIOUS CONNECTIONS OF SPEAKER CORDS General connection using the bare cords 1. Carefully strip about 10 mm(3/8˝) of insulation and twist the wire tip. 2. Loosen the knob and insert the wire. 3. Tighten the knob to fix the wire in place. Connection using the banana plugs 1.

  • Page 8: Speaker Placement

    SPEAKER PLACEMENT Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows : ■ ■ Front left and right speakers and center speaker •...

  • Page 9: Front Panel Controls

    Note on system power control If the DC TRIGGER connection is made between this unit and Sherwood pre amplifier P-965, this unit will be switched between the standby mode and the operating mode automatically each time P-965 is switched between these modes.

  • Page 10: Troubleshooting Guide

    Troubleshooting Guide If a fault occurs, run through the table below before taking your unit for repair. If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your dealer.

  • Page 11: Specifications

    Specifications • Amplifier Section Power output, stereo mode, 8 Ω, THD 0.02 %, 1 kHz | 2× × 125 W 7-CH mode(full channel driven), 8 Ω, THD 0.02 %, 1 kHz | 7× × 100 W 7-CH mode(only channel driven), 8 Ω, THD 0.02 %, 1 kHz | 130 W/CH Total harmonic distortion, 8 Ω, 125 W, 1 kHz | 0.02 % Intermodulation distortion 60 Hz : 7 kHz= 4 : 1 SMPTE, 8 Ω, 125 W | 0.01 %...
  • Page 12 A - 965 7-CH Power Amplifier 5707-04746-001-0...

Table of Contents