Working Advice; Maintenance And Service; Maintenance And Cleaning - Bosch Uneo Maxx Original Instructions Manual

OBJ_BUCH-1250-002.book Page 8 Wednesday, March 9, 2011 8:56 AM
8 | English
Run-on Brake
When the On/Off switch 8 is released, the chuck brakes to a
stop, thus preventing the run-on of the tool.
When driving in screws, wait until the screw is screwed in
flush with the material and then release the On/Off switch 8.
By doing so, the head of the screw does not penetrate into the
material.
Battery Charge-control Indication
The battery charge-control indicator 9 consists of three green
LEDs, and indicates the charge condition of the battery for a
few seconds when the On/Off switch 8 is pressed halfway or
fully.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green
The 3 LEDs of the battery charge-control indicator 9 and the
Power Light 11 flash rapidly when the battery temperature is
not within the operating temperature range of –30 to +65°C.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature of 65 °C is exceeded, the electronic control
switches off the power tool until the temperature is in the op-
timum temperature range again.
The 3 LEDs of the battery charge-control indicator 9 and the
"Power light" 11 flash rapidly when the battery temperature is
not within the operating temperature range of –30 to +65°C
and/or when the overload protection has actuated.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.

Working Advice

Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.

Maintenance and Service

Maintenance and Cleaning

For safe and proper working, always keep the machine
and ventilation slots clean.
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
2 609 004 639 | (9.3.11)
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
Capacity
www.bosch-pt.com
≥ 67%
Our customer service representatives can answer your ques-
34—66%
tions concerning possible applications and adjustment of
11—33%
products and accessories.
≤ 10%
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Bosch Power Tools