Page 1
Document number: ePROU0130 Version V3.0 January 2010 This manual applies to software version 1.46 or later. LSC Lighting Systems (Aust) Pty. Ltd. ABN 21 090 801 675 Building 3, 66-74 Micro Circuit Dandenong South, Victoria 3175 Australia Tel: +61 3 9702 8000...
This manual describes the configuration and each dimmer channel. operation and specifications of the ePRO digital dimmers manufactured by LSC Lighting Systems. The ePRO dimmer utilises Pulse Transformer Fired Dimmer (PTFD) Technology. In essence 1.2 ePRO features...
Permanent installation models have a suitability for the intended application, please special screw termination rear panel that provides consult LSC Lighting Systems or your nearest five 16mm² pressure pad screw terminals to Distributor for further information. connect incoming three phase supply.
ePRO Dimmer Operator Manual V3.0 DIMMER OPERATION display is dependent on which mode the dimmer 3.1 Control Panel is currently in. Under other conditions the display The control panel on the ePRO dimmer is will also scroll prompt and error messages. designed to be concise and easy to operate.
ePRO Dimmer Operator Manual V3.0 indicate “”b-2” (Bank number 2) and then it will Button to “Channel” and selecting the next display channel “13”. Repeat this step to move to channel. If loads are not to be driven during this the next bank.
10 next channel, thus creating the desired scene Amps per dimmer channel. LSC Lighting Systems (group of channels). (Aust) Pty. Ltd. takes no responsibility for any possible damage to lamps operated in this mode.
ePRO Dimmer Operator Manual V3.0 dimmer will exit the Curve function and store the Status Display – “total reset inc – yes dec – curve set up into memory. The “Curve” LED will no”. Press the decrement button to move to the remain on, indicating that stored curve set ups are next menu.
Dimmer Operator Manual V3.0 SOFTWARE UPGRADES 4.2 Installing and Running CodeLINK LSC Lighting Systems has a corporate policy of Close any open applications on your computer for continuous improvement to its products. The the duration of the upgrade process.
ePRO Dimmer Operator Manual V3.0 DMX EXPLAINED DMX512A is the industry standard for the 5.1 Cable selection transmission of digital control signals between Do not use unscreened microphone or low speed lighting equipment. It utilises just a single pair of data cables for DMX.
ePRO Dimmer Operator Manual V3.0 MAINTENANCE The ePRO dimmer has been designed to provide years of trouble free service when maintained and operated within the specifications detailed in this operator manual. 6.1 Routine maintenance The ePRO dimmer requires minimal maintenance to operate at optimum performance.
ePRO Dimmer Operator Manual V3.0 7.2 Load Socket Wiring The following pages detail the load socket wiring options available on the ePRO dimmers. Socapex 19 Pin Multipole Connectors Connector #1 Function Connector #2 Function Pin 1 Chan 1 Active Pin 1 Chan 7 Active Pin 2 Chan 1 Neutral...
Page 15
ePRO Dimmer Operator Manual V3.0 Wieland and Harting 16 Pin Multipole Connectors Connector #1 Function Connector #2 Function Pin 1 Chan 1 Active Pin 1 Chan 7 Active Pin 2 Chan 2 Active Pin 2 Chan 8 Active Pin 3 Chan 3 Active Pin 3 Chan 9 Active...
Page 16
ePRO Dimmer Operator Manual V3.0 6 Channel with screw terminals 12 Channel with screw terminals...
In any event, LSC Lighting Systems (Aust) Pty. Ltd. can not be held liable for any direct, indirect, special, incidental, or consequential damages or loss whatsoever (including, without limitation, damages for loss of profits, business interruption, or other pecuniary loss) arising out the use or the inability to use this product for its intended purpose as expressed by the manufacturer and in conjunction with this operating manual.