Related Manuals for LSC DP-610
Summary of Contents for LSC DP-610
- Page 1 English USER'S MANUAL CHANNELS ON DP-610 6 CHANNEL DMX & ANALOG DIMMER PACK LIGHT STREAM CONTROLS CH.1 CH.3 CH.5 CH.2 CH.4 CH.6 CHANNELS MENU DOWN Please read before use...
-
Page 3: Table Of Contents
Contents Features 1 General Instructions 2 1. Overview 3 1.1 Front View 3 1.2 Rear View 5 2. Menu System 7 2.1 Beginning Menu 7 2.1.1 Adjust channel intensity temporarily 7 2.1.2 Adjust whole intensity temporarily 7 2.2 Basic Menus 8 2.2.1 DMX fail 8 2.2.2 Phase Correction 9 2.2.3 DMX Address 10... -
Page 4: Features
Features Thank you for your purchase. This product features include: Microcomputer control Separate DMX addressing for each channel Each channel can be programmed with the DMX address, and the preheat of the lamps 12 chase programs can be recalled as required, chase speed is adjustable Chase programs 1-12, DMX Hold, Analogue can be selectable in the event that DMX failure. -
Page 5: General Instructions
General Instructions Please read through this operating instructions before installing or using your new product. After you have finished reading the instructions, put them away in a safe place for future reference. WARNING! This product must be earthed. To prevent fire or shock hazard, do not expose this product under high temperature or moisture area. -
Page 6: Overview
1. Overview 1.1 Front View... - Page 7 1. Overview 1.1 Front View 1. 2x8 LCD Display Shows the current activities or adjustments of menus. 2. Channel LEDx6 These LEDs show the activities of corresponding channels. 3. DMX LED This LED blinks when DMX signal is present. 4. Channel Buttonx6 These buttons are used to change the intensity of corresponding channel.
-
Page 8: Rear View
1. Overview 1.2 Rear View 1. Power Input AC 120V~50/60Hz,60A max. 2. Terminal Output Single phase: 10A/CH., Total 60A Three phase: 10A/CH., Total 20A 3. DMX OUTPUT This connector sends DMX signal through to the next DMX device. . DMX INPUT This connector accepts DMX input signal. - Page 9 1. Overview 1.2 Rear View...
-
Page 10: Menu System
2. Menu System 2.1 Beginning Menu Apply power to this unit, firstly the LCD reads the revision of software, then Beginning Menu is displayed. Beginning Menu consists of a row of dynamic images and a row of characters , the first row represents the intensity value, and the second row indicates the channel. -
Page 11: Basic Menus
2. Menu System 2.2 Basic Menus In Beginning Menu, tap MENU button to Dmx fail enter Basic Menus system. There are 5 menus: DMX Fail, Phase Correction, DMX Address, Preheat and Curve, you can use UP/DOWN button to MENU UP DOWN ESC scroll through the menus. -
Page 12: Phase Correction
2. Menu System 2.2.1 DMX Fail Speed 4. If you select Prog. 1-12, tap ESC button, speed 00.4s menu is activated,. You can select the chasing speed from 0.1 to MENU UP DOWN ESC 20 seconds using UP/DOWN button. Speed After you've finished your setting, tap ESC 00.4s button to exit. -
Page 13: Dmx Address
2. Menu System 2.2.3 DMX Address Dmx addr 1. Tap UP/DOWN button to scroll to DMX Address menu. MENU UP DOWN ESC 2. Tap MENU button to enter sub-menu Dmx addr system. You can use UP/DOWN button Block to select Block/Single. [Block]: Complete dimmer(6 channels) has only MENU UP DOWN ESC... -
Page 14: Preheat
2. Menu System 2.2.3 DMX Address Chan[1] 5. In Single mode, tap MENU to select between [001] channel and address. MENU UP DOWN ESC 6. When channel is activated, tap UP/DOWN Chan[1] button to select from [1-6]; when address is [001] activated, tap UP/DOWN button to select from[001-512]. - Page 15 2. Menu System 2.2.4 Preheat 2. Tap MENU button to enter sub-menu Preheat system. MENU UP DOWN ESC 3. Tap UP/DOWN button to select between All/Single mode, and tap MENU to enter All/Single mode. Preheat [000%] MENU UP DOWN ESC MENU UP DOWN ESC 4.
-
Page 16: Curve
2. Menu System 2.2.4 Preheat 6. When channel is activated, tap UP/DOWN Chan[1] button to select from [1-6]; when preheat is [050%] activated, tap UP/DOWN button to select from [000%-050%]. MENU UP DOWN ESC Preheat 7. Tap ESC button to exit. MENU UP DOWN ESC 2.2.5 Curve... - Page 17 2. Menu System 2.2.5 Curve 3. Tap UP/DOWM button to select from Linear/ Curve Switch/Square. Linear MENU UP DOWN ESC 4. Tap ESC button to exit. Curve MENU UP DOWN ESC 5. You can tap ESC button to return to Beginning Menu.
-
Page 18: Technical Specifications
Technical Specifications Power Input ............AC 120V~50-60Hz Channel Output(Single phase)......10A/CH., Total 60A Channel Output(Three phases)..10A/CH., Total 20A per phase DMX Output ..........3 pin female XLR socket DMX Input ............. 3 pin male XLR socket Analogue Input ..........0-10V, 8-pin DIN socket Dimensions .............. - Page 20 24-004-0893 Printed in China All rights reserved Rev 1.0 January 2003...