Page 2
The Vitec Group plc Beijing Representative Office Room 706, Tower B Derun Building, YongAn Dongli A No.3 Jianwai Ave., Chaoyang District Beijing, P.R.China 100022 ® Clear-Com, CellCom/FreeSpeak and the Clear-Com Communications Systems logo are registered trademarks of The Vitec Group plc. Website: www.clearcom.com...
REPAIR POLICY ........W-viii Clear-Com Communication Systems...
Page 4
Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
Page 5
Do not place naked flame sources such as candles IFB-104 Interface. on or near an IFB-104 Interface. (4) Only use attachments/accessories specified by Clear-Com Communication Systems. (5) Unplug the IFB-104 Interface during lightning storms or when unused for long periods of time.
Page 6
Do not open the product's case. This symbol informs you that important operating and main- tenance instructions are included in the literature accompanying this product. Figure 1: Safety Symbols Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
IFB-related, but can contain other program material. The front panel has only one indicator. This indicator lights up when power is connected to the IFB-104. Power is only necessary if the talent receivers require it. Clear-Com Communication Systems 1 - 1 IFB-104 Interface Instruction Manual...
Page 8
1 - 2 Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
5. Move the slide switch to WET if the on-air talent receiver requires power and to DRY if it doesn’t require power. Use the WET setting with a Clear-Com talent receiver. 6. Connect power to the appropriate connector on the left of the back panel.
Page 10
2 - 2 Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
LED GREEN R/A PC MOUNT LED LED 2.7K OHM 1/4 Carbon Film 5% S101 S201 S301 S401 Switch DPDT SLIDE SWTCH T101 T102 T201 T202 Transformer 600CT/600CT T301 T302 T401 T402 Clear-Com Communication Systems 3 - 1 IFB-104 Interface Instruction Manual...
Page 12
Figure 3-2: IFB-104 Schematic 3 - 2 Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
100 Hz to 15 kHz, +/- 2 dB Temperature Operating 0° to 50° C (32° to 125° F) Storage 0° to 70° C (32° to 150° F) Humidity Operation and Storage 20% to 90%, non-conducting Clear-Com Communication Systems 4 - 1 IFB-104 Interface Instruction Manual...
Page 14
Performance specifications included in this manual are design-center specifications and are included for customer guidance and to facilitate system installation. Actual operating performance may vary. 4 - 2 Clear-Com Communication Systems IFB-104 Interface Instruction Manual...
EMS Element Management System. Software program that is used to manage the Concert server system resources. Ethernet International standard which describes how information is transmitted across a network. Provides for the efficient organization of network components. Clear-Com Communication Systems 5 - 1 Eclipse Glossary...
Page 16
Single mode fiber, with its smaller core, concentrates the light beam so that it carries signals further. Multimode fiber was the first type of fiber offered 5 - 2 Clear-Com Communication Systems Eclipse Glossary...
Page 17
Source In this manual, the term “source” refers to a device—such as an intercom panel, interface, or beltpack —that sends audio into the matrix. The device to which audio is sent is called a “destination”. Clear-Com Communication Systems 5 - 3 Eclipse Glossary...
Page 18
Each signal is assigned a particular wavelength on the light spectrum and therefore many signals can be transmitted simultaneously without interfering with each other. 5 - 4 Clear-Com Communication Systems Eclipse Glossary...
(1) Cables, accessories, components & consumable items have a Limited Warranty of 90 days. (2) Any Clear-Com product that has been classified as obsolete at the time of sale has a Limited Warranty of 90 days from sales and will be replaced with the same product or a sales credit will be issued, at the sole discretion of Clear-Com.
Page 22
Limited Warranty for their type 1.i 1 - 1.i.5 as above. d) Any Clear-Com product that is repaired or supplied as a replacement under the terms of this Limited Warranty shall inherit the remaining warranty period from the original product.
Page 23
Clear-Com determines is not a result of failure in the Services provided by Clear-Com. Further Services excluded from this Agreement include: services required due to errors or omissions in Customer purchase orders;...
Page 24
Clear-Com Communication Systems Standard Limited Warranty...
TECHNICAL SUPPORT & REPAIR POLICY NOVEMBER 1, 2008 In order to ensure that your experience with Clear-Com and our World Class products is as beneficial, effective and efficient as possible, we would like to define the policies and share some "best practices"...
+1 510 337 6600 Email: CustomerServicesAPAC@vitecgroup.com d) Email Technical Support is available for all Clear-Com branded products free of charge for the life of the product, or two years after a product has been classified as obsolete, whichever comes first.
Page 27
During the first 30 days of the Standard Warranty Period: Once the equipment fault has been verified by Clear-Com or its authorized representative, Clear-Com will ship a new replacement product. The Customer will be provided with an RMA number and be required to return the faulty equipment within 14 days of receipt of the replacement or will be invoiced for the list price of a new product.
The Customer will be provided with an RA number upon contacting Clear-Com Customer Services as instructed below. c) The RA number must be obtained from Clear-Com via phone or email prior to returning product to the Service Center. Product received by the Service Center without a proper RA number is subject to return to the Customer at the Customer's expense.
Page 29
Email: TechnicalSupportEMEA@vitecgroup.com vii) Note: Clear-Com's Limited Warranty does not cover normal wear and tear. The Customer will be charged the full cost of the repair if their equipment has been tampered with by non-approved personnel, or has been subject to damage through electrical failure, liquid damage or mishandling.
Need help?
Do you have a question about the Eclipse IFB-104 and is the answer not in the manual?
Questions and answers