Advertisement
Quick Links
®
Stealthbox
I N S T A L L A T I O N G U I D E
for the
SB-GM-BURBSCNSL/10W3v2
(2003-Up Chevrolet Suburban,Tahoe,
Silverado &
GMC Yukon,YukonXL, Sierra with front
bucket seats and center console)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbox
responsibly.
w w w . j l a u d i o . c o m
START
HERE
Read the instructions completely, before the start of
➔
the install.
This Stealthbox Enclosure install does require per-
manent modification to the OEM inner console.
➔
STEP 3: Pull the cup holders up and out of the
center console.
S B - G M - B U R B C N S L / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5
➔
STEP 1: Engage the emergency brake.
Place the key into the ignition and turn to the accessory posi-
tion.
The shifter and the steering wheel needs to be posi-
tioned all the way down.
Remove the front dash cluster panel, by pulling the dash trim
towards you and work around the diameter. Be careful not to
damage the four way light push button, located on top of the
steering column.
Once the trim is removed. Place the transmission into park,
remove the key from the ignition and pop the emergency brake.
➔
STEP 4:
On the upper lip of the main storage
bucket, remove all the screws, including the storage
lid's screws.
Pa g e 1
➔
STEP 2: Moving down to the top portion of the
center console. Pull the upper storage pocket panel
out and disconnect the electrical outlets.
➔
STEP 5: To remove the main storage bucket,
remove the rubber mat.This will expose the four
screws that need to be removed.
Once all these screws have been removed. Remove
the storage bucket by lifting up and out of the con-
sole.
Continued on Next Page ➔
S h e e t S K U # 0 1 1 1 6 7 3 / 0 8 / 2 0 0 5
Advertisement
Related Manuals for JL Audio Stealthbox SB-GM-BURBCNSL/10W3v2
Summary of Contents for JL Audio Stealthbox SB-GM-BURBCNSL/10W3v2
- Page 1 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration. Please enjoy your JL Audio Stealthbox responsibly. w w w . j l a u d i o . c o m S B - G M - B U R B C N S L / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5 ➔...
- Page 2 *CAUTION* Cont. The vehicle that you are working on might be From equipped with side impact air bags.To remove the Previous front seats, please follow these required procedures. Page ➔ ➔ 1)Disconnect the ground wire from the negative side of the battery. 2)Let the vehicle sit for 15 minutes.This allows the air bags to discharge.
- Page 3 Cont. From Previous Page ➔ ➔ STEP 12: Remove the OEM wire harness from the plastic track. Wrap the OEM wiring in black tape. ➔ STEP 16: When the Stealthbox is removed, the wax square should have the impressions of the socket cup set screws.
- Page 4 Cont. From Previous Page ➔ ➔ STEP 20: Back out the socket cup set screws to expose 1-1/2”. Carefully guide the socket cup set screws through the mounting holes, in the floor. From under the vehicle, snug tighten the Stealthbox using the supplied hardware.You want a little play in the mounting assembly, to allow proper line up with OEM console in future steps.
- Page 5 Cont. From Previous Page ➔ ➔ STEP 28: This is a view of the driver’s side, front area. The mark lines needs to follow this edge forward, to this mounting leg. (Arrow) The mark line needs to follow up this mounting leg and stop at this upper wall edge.
- Page 6 Cont. From Previous Page ➔ ➔ STEP 36: This the view of the passenger’s side, from STEP 29. ➔ STEP 40: The upper mark line goes across the top, using this exposed front edge. w w w . j l a u d i o . c o m S B - G M - B U R B C N S L / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5 ➔...
- Page 7 Cont. From Previous Page ➔ STEP 44: The pair of 10mm bolts that where removed in STEP 5, need to be replaced.You may have to reposition the OEM console, to have it line up like factory. STEP 47: Replace the rear of the outer cosmetic console and the four mounting screws from STEP 21.
- Page 8 Cont. Power Handling: 300Watts JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.