American DJ Spherion Tri LED User Instructions page 5

Spherion Tri LED
Blackout Blackout the unit
1. Synchronous Strobe in white
Function 2. Asynchronous Strobe in whtie
3. Sound Strobe in color
Sound
Mode
(LED OFF)
Spherion Tri LED
Disconnect the unit's main power supply. Insert a standard flat head
screw driver in to the fuse holder housing. Turn the screwdriver in
counter-clockwise direction to remove the fuse holder. Remove the
old fuse and discard it, replace the fuse with the same type. Insert
the fuse holder back into it's housing and turn in clockwise direction
to lock the holder in place.
Spherion Tri LED
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
American DJ - www.americandj.com - Spherion Tri LED Instruction Manual Page 16
© ®
UC3 Control
Select color
1. Red
2. Green
3. Blue
Select
4. Red+Green
Show(1-7)
5. Green+Blue
6. Red+Blue
7. Red+Green+Blue
8. Color change by sound
Show(LED
Manual Color
slow
(LED ON)
blinking)
Fuse Replacement
Cleaning
Spherion Tri LED
Power Supply:
The American DJ
tronic ballast, which will auto sense the voltage when it is plugged into
the power source. With the electronic ballast you do not need to worry
about wall voltage, this unit can be plugged in anywhere.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX
fixtures (most controllers only have a DATA "OUT" terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Spherion Tri LED can be controlled via DMX-512 pro-
tocol. The Spherion Tri LED can be either a 1 or 3 channel DMX unit.
The DMX address is set electronically using the
controls on the rear panel of the unit. Your unit and
your DMX controller require a approved DMX-512
110 Ohm Data cable for data input and data output
(Figure 1). We recommend Accu-Cable DMX cables.
If you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable
may be purchased at almost all professional sound
and lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also
American DJ - www.americandj.com - Spherion Tri LED Instruction Manual Page 5
© ®
Set Up
Spherion Tri LED contains a elec-
®
Figure 1