Page 1
RDG100KN Room thermostat with KNX communications For fan coil unit applications For universal applications KNX bus communication (S-mode and LTE mode) Backlit display 2P / PI / P control Outputs for on/off, PWM or 3-position control ...
Page 2
The RDG100KN room thermostat is designed for use with the following types of system: Fan coil units via ON/OFF or modulating control outputs: 2-pipe system 2-pipe system with electric heater 2-pipe system and radiator / floor heating ...
Page 3
Use P46 / P47 to change output from ON/OFF (factory setting) to PWM Use DIP switches 4 and 5 to change output from ON/OFF to 3-position 3 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 4
Use P46 / P47 to change output from ON/OFF (factory setting) to PWM Use DIP switches 4 and 5 to change output from ON/OFF to 3-position 4 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 5
AC 230 V 1) ON/OFF, PWM or 3-position (triac outputs) Ordering When ordering, indicate both product number / stock number and name: E.g. RDG100KN / S55770-T163 room thermostat Order valve actuators separately. Equipment combinations Data Description Product no.
Page 6
Adapter plate 112 x 130 mm for surface wiring ARG70.2 N3009 KNX Power supply 160 mA (Siemens BT LV) 5WG1 125-1AB01 KNX Power supply 320 mA (Siemens BT LV) 5WG1 125-1AB11 KNX Power supply 640 mA (Siemens BT LV)
Page 7
Confirmation of parameters Fault Temporary timer function; visible when operating mode is temporarily extended (extended presence or absence) Indicates that room temperature is displayed 7 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 8
AC 230 V mains voltage. No cables provided with a metal sheath. Disconnect from supply before removing from the mounting plate. 8 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 9
RS232 KNX interface (e.g. Siemens N148 / UP146 / UP152) OCI700 USB- KNX interface Note An external KNX bus power supply is required if an RDG100KN is connected directly to a tool (ACS or ETS3) via KNX interface. 9 / 14 Siemens...
Page 10
2002/96/EC (WEEE) and may not be disposed of as unsorted municipal waste. Adhere to all relevant national laws. Regarding disposal, use the systems setup for collecting electronic waste. Observe all local and applicable laws. 10 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 11
Accuracy at 25 °C < ± 0.5 K Temperature calibration range ± 3.0 K Settings and display resolution Setpoints 0.5 °C Current temperature value displayed 0.5 °C 11 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 12
CM1Y9775 DESIGO RXB integration – S-mode CM1Y9776 DESIGO RXB / RXL integration – individual addressing CM1Y9777 Third-party integration CM1Y9778 Synco integration CM1Y9779 Working with ETS 12 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...
Page 13
B1, B2 Temperature sensor (return air tempe- and electric rature, external room temperature, heater changeover sensor, etc.) KNX data + 4-pipe CE– KNX data – and electric heater 13 / 14 Siemens RDG100KN Room thermostat with KNX communications CE1N3191en Building Technologies 01 Jun 2010...