Timer Recording; Using Show Iew System To Make Timer Recordings - Panasonic Diga DMR-ES10 Operating Instructions Manual

Timer recording

e.g.,
Continental Europe
e.g.,
Continental Europe
Numbered
buttons
CANCEL
g
h
DIRECT NAVIGATOR
DIRECT
NAVIGATOR
TOP MENU
SUB MENU
PROG/
CHECK
* REC
REC MODE
RAM -R -RW(V) +R
You can enter up to 16 programmes up to a month in advance.
Preparation
•
Turn on the television and select the appropriate video input to suit
the connections to this unit.
•
Check the time on the unit is correct.
For Continental Europe
Using S V
HOW
recordings
Entering S V numbers is an easy way of timer recording. You
HOW IEW
can find these numbers in TV listings in newspapers and magazines.
1
Press [ShowView].
ShowView
Enter ShowView Number by using 0-9 key.
2
Press the numbered buttons to enter
the S V
HOW
•
To correct the number
Press [w] to move back to correct a digit.
RQT8020
18
OPEN/CLOSE
EXT LINK CH
g
For Continental Europe
EXT LINK
For Continental
Europe
ShowView
For Australia,
ShowView
N.Z. and Asia
INPUT SELECT
CANCEL
MANUAL SKIP
G-Code
INPUT
SKIP SLOW/SEARCH
SELECT
q
FUNCTIONS
e, r, w, q
ENTER
RETURN
PROG/CHECK DISPLAY
STATUS TIME SLIP
REC REC MODE EXT LINK TIMER
z TIMER
CREATE
AUDIO ERASE F Rec
CHAPTER
For Continental
Europe
EXT LINK
Linked timer
recording with
external
equipment
(e.g., digital/
satellite
receiver)
system to make timer
IEW
Remain 1:58 SP
12:53:00 15. 7. TUE
number.
IEW
3
Press [ENTER].
TIMER
RECORDING
REC
Name
1 ARD
•
Confirm the programme and make corrections if necessary
using [e, r, w, q] (➔ page 20, Manually programming timer
recordings, step 3).
•
When "-- -----" appears in the "Name" column, you cannot
set timer recording. Press [e, r] to select desired
programme position. After you have entered the information
of a TV station, it is kept in the unit's memory.
•
You can also press [REC MODE] to change the recording
mode.
•
VPS/PDC (➔ below)
←→
ON
•
Programme Name
Press [w, q] to select "Programme Name" and press
[ENTER] (➔ page 34).
4
Press [ENTER].
The settings are stored.
TIMER
RECORDING
No. Name
01 ARD 1 15. 7. TUE
Repeat steps 1–4 to programme other recordings.
5
Press [z TIMER].
The unit turns off and "z" lights on the unit's display to
indicate timer recording standby has been activated.
RAM
Even if the unit is in timer recording standby, play starts when you
press [q] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
■ To release the unit from recording standby
Press [z TIMER].
The unit turns on and "z" goes out.
•
Be sure to press [z TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "z" is displayed.
■ To cancel recording when recording has
already begun
Press [z TIMER].
•
You can also press and hold [g] on the main unit for more than 3
seconds to stop recording.
Note
•
"z" flashes for about 5 seconds when the unit cannot go to timer
recording standby (e.g., a recordable disc is not in the disc tray).
•
If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "z" flashes on the unit display. In this case,
press [z TIMER] to put the unit in the timer recording standby
mode.
•
When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part at
the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R, DVD-RW (DVD-Video format) and +R).
■ VPS/PDC function (➔ page 42)
As long as a VPS/PDC signal is being broadcast by the TV station,
even if the broadcast programme time changes, the recording time
automatically changes to match the new broadcast time.
To activate the VPS/PDC function
In step 3 in the VPS/PDC column, press [e, r] to select "ON".
Remain 1:58 SP
12:54:00 15. 7. TUE
VPS
Date Start Stop Mode PDC
15. 7. TUE 19:00 20:00 SP - - -
Programme Name
OFF (---)
Remain 1:58 SP
12:55:00 15. 7. TUE
VPS
Disc
Date Start Stop Mode
space
PDC
Check to make
19:00 20:00 SP - - - OK
New Timer Programme
sure "OK" is
displayed.