Clarke Super 7R Operator's Manual

Clarke Super 7R Operator's Manual

Dc edger
Hide thumbs Also See for Super 7R:

Advertisement

Super 7R
Operator's
DC Edger
Manual
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine
before using it. If you cannot read English, have this manual explained fully before attempting to
operate this machine.
Si Ud. no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el
manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke
®
, 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 70895A 11/04
Printed in the U.S.A.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Super 7R and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clarke Super 7R

  • Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
  • Page 2: Table Of Contents

    Adjustment Procedures ..............9 Routine Maintenance..............9 Maintenance ................10 Parts and Service Manual - Section II Assembly Drawing ..............12 Assembly Parts List ..............13 Wiring Diagram ................14 Page 2 Clarke ® American Sanders Super 7R Operator's Manual...
  • Page 3: Operator Safety Instructions

    • Do not empty the contents of the dust bag into a fire. • Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to countersink all nails before sanding floors. ® Clarke American Sanders Super 7R Operator's Manual Page 3...
  • Page 4 Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty. Servicing of this unit must always be referred to an authorized Clarke American Sanders distributor. CAUTION: Use of this equipment to move other objects or to climb on could result in injury or damage.
  • Page 5: Machine Specifications

    2800 RPM 2800 RPM Disc Driver System Gear Driven Gear Driven Power Cable 14-3 Gray Rubber 14-3 Gray Rubber Dust Collection Standard Standard Dust Control Rate 110 CFM 110 CFM ® Clarke American Sanders Super 7R Operator's Manual Page 5...
  • Page 6: Sanding Cuts And Sandpaper

    120 grit For final sanding of certain conifers. 945605/500 150 grit For final sanding of certain conifers where a 945606/300 smooth surface is desired for surface roughening between coats of finish. Page 6 Clarke ® American Sanders Super 7R Operator's Manual...
  • Page 7: Machine Set-Up

    4. To empty the dust bag, unzip the disposal flap and force contents out by inverting the bag. NOTE: For best results, empty frequently. Follow all warnings posted in this manual and on the dust bag. ® Clarke American Sanders Super 7R Operator's Manual Page 7...
  • Page 8: Operating Instructions

    Empty dust bag into a metal container, clear of any combustibles. Do not empty content into a fire. Do not overfill dust bag. Page 8 Clarke ® American Sanders Super 7R Operator's Manual...
  • Page 9: Adjustment Procedures

    The machine comes fully lubricated. The gears in the gear box have enough lubrication for approximately six months of normal operation. Have the lubricant changed at least every 6 months or more frequently under heavy use. ® Clarke American Sanders Super 7R Operator's Manual Page 9...
  • Page 10: Maintenance

    If none appears it may be necessary to add additional lubricant. Figure 7 10. Wipe off excess lubricant and clear vent hole. Page 10 Clarke ® American Sanders Super 7R Operator's Manual...
  • Page 11 Super 7R Edger Section II Parts and Service Manual (70895A) ® Clarke American Sanders Super 7R Operator's Manual Page 11...
  • Page 12: Parts And Service Manual - Section Ii Assembly Drawing

    Super 7R Edger Drawing - 11/04 60 47 ® Page 12 Clarke American Sanders Super 7R Operator's Manual...
  • Page 13: Assembly Parts List

    Eject Disc Cutter & 72. 315604 Mallet 317004 Punch Center 317304 Ring Disc Cutter 762005 Clamp 920208 Nut - ¼-20 Hex 962013 Screw ¼-20 x 1¼ R 962233 Screw ¼-20 x ® Clarke American Sanders Super 7R Operator's Manual Page 13...
  • Page 14: Wiring Diagram 11/04

    Model Super 7R Edger Wiring Diagram 11/04 Page 14 Clarke ® American Sanders Super 7R Operator's Manual...
  • Page 15 29815 John R. Gilwilly Industrial Estate (810) 544-6300 Penrith Cumbria CA11 9BN ® American Lincoln / Clarke, Marietta, Georgia 30066 +44 1768 868 995 1455 Canton Road (770) 973-5225 ALTO France S.A. Strasbourg B.P. 44, 4 Place d’Ostwald F-67036 Strasbourg...
  • Page 16 (b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.

This manual is also suitable for:

American sanders super 7r

Table of Contents