Troubleshooting; Snooze Function - TDK iCUBIC Setup Manual

Alarm Clock Operation
During the unit in standby mode.
To set the correct "Alarm 1"
• Press the "Alarm 1" button once on the remote control only. The "AL 1 bell symbol" indicator will light
on and the "Hour" indicator will flash too. Adjust the correct "Hour" by pressing the "Skip/search" (up
or down) button.
• Press the "Alarm 1" button twice. The "AL 1 bell symbol" indicator will light on and the "Minute"
indicator will flash too. Adjust the correct "Minute" by pressing the "Skip/search" (up or down) button.
• Press the "Alarm 1" button again to select to tuner, iPod, buzzer to set the desire alarm mode status.
• Press the "Alarm 1" button repeatedly to confirm the "Alarm 1" function, the "Hour/minute" indicator
will become to "Clock" and the "AL 1 bell symbol" indicator will light on the LCD display.
To set the correct "Alarm 2"
• Press the "Alarm 2" button once on the remote control only. The "AL 2 bell symbol" indicator will light
on and the "Hour" indicator will flash too. Adjust the correct "Hour" by pressing the "Skip/search" (up
or down) button.
• Press the "Alarm 2" button twice. The "AL 2 bell symbol" indicator will light on and the "Minute"
indicator will flash too. Adjust the correct "Minute" by pressing the "Skip/search" (up or down) button.
• Press the "Alarm 2" button again to select to tuner, iPod, buzzer to set the desire alarm mode status.
• Press the "Alarm 2" button repeatedly to confirm the "Alarm 2" function, the "Hour/minute" indicator
will become to "Clock" and the "AL 2 bell symbol" indicator will light on the LCD display.

Snooze Function

When the alarm sounds, press the snooze button. The alarm will go off and come on again in
approximately 5 minutes. You may repeat this cycle several times during the 1 hour alarm cycle.
Note:
• In any time, you can press the "standby" button once on the unit or remote control to stop the "Alarm
1 or 2" function. The "AL 1 or 2 bell symbol" indicator will still light on the LCD display. (It may keep
the "Alarm 1 or 2" function in next day)
• In any time, if you want to stop the "Alarm 1 or 2" function fully, you can press the "Alarm 1 or 2"
button once on the remote control only. The "AL 1 or 2 bell symbol" indicator will turn off on the
display. The function of the "Alarm 1 or 2" will cancel at once.
15

Troubleshooting

Symptom Possible Cause
Screechy, The sound volume level of the main
abrasive, system is too high.
unclean
sound.
Input signal is too strong.
Distorted
(in case of headphone terminals)
sound.
The bass boost function of the player
is turned on while connected to the
headphone terminal.
The adapter is not plugged into an
No sound.
AC power outlet.
Volume
level is
The POWER switch of the main
too low.
system is in the OFF position.
The connection (input) cable is not
properly connected.
Line output terminal connection
Headphone terminal connection
The volume on the system is set to
minimum.
The volume of the connected device is
set too low. (headphone terminal)
A commercially available resistance
cable is used for the connecting cable.
Remedy
Turn the Volume control to decrease the volume.
Adjust to a level lower than medium level using
volume of connection device as a reference.
Switch off the bass boost function of the player.
Plug the adapter into a proper AC power outlet.
Turn the POWER switch ON.
Check that the cable is connected to the line output
terminal on the connecting device and the INPUT
terminal on the main system.
Check that the cable is connected to the
headphone terminal on the connecting device and
the INPUT terminal on the main system.
Turn the VOLUME control on the main system to
increase the volume.
Adjust to a level higher than medium level using
volume of connection device as a reference.
Use a connecting cable without resistance.
16