Parts List - Band-it Ultra-Lok UL9010 Operating Instructions Manual

Parts List

Notes:
Apply Item 31 (Grease) to:
Item 4 (Cut off cam)
Item 3 (Cutter knife) at contact point with item 1 (Tool head)
Item 26 (Spring) before installation
Apply Item 32 (Grease) to:
Item 7 (Tension screw) threads and grooved end
Item 2 (Cutter blade) counter-bore only, after item 14 (bearing tip) has been installed.
Tighten the following:
Item 23 (#10-32 Screws)
to 60 – 70 in-lbs.
Item 22 (1/4-28 Screws)
to 90 – 110 in-lbs.
Adjust Item 24 (Plunger) for
positive detent action when
item 6 (Handle) is actuated.
Part M09887, Shear Plate has
two cutting edges. This part
can be rotated to use the second
edge prior to replacement.
NOTE:
Part M09387, (Optional)
½" Shear Plate -
Required replacement for # 33
M09887 shear plate in order to
install ½" wide Ultra-Lok
Clamps
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
Ph: 1-800-525-0758
Fax: 1-800-624-3925
Item Part Number Quantity
1 M00587
2 M09787
3 M08687
4 M08987
5 M09087
6 UL1219
7 M00987
8 M08887
9 M01787
10 M09187
11 M02387
12 M00287
13 M01388
14 M05387
15 M06587
16 M02287
17 M04387
18 M07387
19 M07487
20 M07587
21 M05787
22 J67287
23 M06187
24 M02487
25 A33887
26 A53587
27 M01487
28 M08187
29 M08087
30 M07987
31 I16387
32 C23199
33 M09887
34 M09387
35 M07687
36 M08288
www.BAND-IT-IDEX.com
Page 6 of 14
Ultra-Lok
1 Tool Head, Fin. UL
1 Cutter Blade, UL
1 Cutter Knife, UL
1 Cam, Cut-off, UL
1 Tension Block, Mach., UL
Handle Assembly: Includes Handle, Handle
1
Grip, and Pins
1 Tension Screw, Fin.
1 Gripper, UL
1 Plate, Back, Cast/Fin.
1 Gripper Guide, UL
1 Plate, Release, cast/fin.
1 Roller, Cut-off, Fin.
1 Pin, .187 Dia X 1.50 Long, Fin.
1 Bearing Tip, Fin.
1 Ball, ¼" Diameter
1 Tip, Load Bearing, Fin.
1 Tripper Bracket, Cast/Fin.
1 Body, Left, Finished, UL
1 Body, Right, Finished, UL
2 Wear Plate, Fin.
2 Screw, Socket Head Cap, ¼ X 1"
4 Screw, Socket Head Cap, ¼ X ½"
4 Screw, Socket Head Cap, #10-32 X 3/8"
2 Screw, Spring Plunger, ¼-20
1 Spring, Compression, .180 X .813 Long
2 Spring, Compression, .300 X 1.00 Long
1 Pin, Dowel, ¼ Dia X 1.50 Long
4 Washer, .128 ID X .238 OD
4 Rivet, Blind, .125 X .328 Long
2 Threaded Insert, #10-32
- Lubricant, Super Lube w/ Teflon
- Lubricant, Moly, Syringe
1 Shear Plate, ¾", UL
1 Shear Plate, ½", UL (Optional)
1 Tool Adapter #1
1 Adapter Clamp
Document # P44987 Rev. N
UL9010
®
Tool
Description
© Copyright
BAND-IT-IDEX, Inc. 2011
All rights reserved