Page 1: Table Of Contents
TEL 0044 191 490 1547 FAX 0044 477 5371 © Copyright TEL 0044 117 977 4647 FAX 0044 977 5582 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 WWW.THORNEANDDERRICK.CO.UK Denver, CO 80216-0307 USA All rights reserved Page 1 of 14 P: 1-800-525-0758...
Page 2: Safety Guidelines
Hose, fitting and clamp must be compatible with each other and the environment used in. If in doubt, consult the hose or fitting manufacturer or call BAND-IT. Clamping objects other than hose requires similar precautions.
Page 3: Setup Instructions
2. Charge drill according to the operator‟s manual for the DeWalt cordless drill. 3. To mount drill onto Band-It Ultra-Lok tool: First use the two #10-32 x 3/8” screws supplied with tool to tighten tool adapter body to the tool. With adapter clamp on tool adapter body, insert drill into back of tool through the adapter clamp.
Page 4 BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 4 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 5: Settings
Use of alternate drills must be approved in writing by the Director of Engineering at BAND-IT-IDEX, jamming up. Excessive use of this feature will wear clutch mechanism and/or tension screw out Inc. Disregard of this caution voids the warranty of the tool and releases BAND-IT of any and all liabilities arising prematurely.
Page 6: Parts List
Shear Plate, UL, ½” (Optional) M09387 BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 6 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 7: Troubleshooting
2. Safety clutch between drill and tool releases prematurely: Make sure tool is fully seated on drill. (see page 4) If problem still remains, contact BAND-IT technical support. Note: To prevent over-travel safety clutch wear, do not over-use safety clutch.
Page 8: Assembly Instructions
See page 6 for parts list BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 8 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 9: Clamp Application
Correct position of tool while tensioning BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 9 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 10 BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 10 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 11 Flow. Finally, complete clamp by tapping down the buckle shroud as described above. BAND-IT-IDEX, Inc. Document # P07886 Rev. L A Unit of IDEX Corporation www.BAND-IT-IDEX.com © Copyright 4799 Dahlia Street BAND-IT-IDEX, Inc. 2010 Denver, CO 80216-0307 USA All rights reserved Page 11 of 14 P: 1-800-525-0758 F: 1-800-624-3925...
Page 12 Syringe. Reorder #C23199 screw. To order more lubricant, specify BAND-IT #C23199 2. Every 500-1000 clamps, depending on tension setting, inspect and repack front bearing with same lubricant. Turn load bearing tip and small bearing tip over for a new bearing surface.
Page 13 Note: Drills needing repair must be forwarded to an authorized „DeWalt‟ repair center in your area. Be sure to remove BAND-IT safety clutch (M21790) from drill. DeWalt Drill is covered solely by the DeWalt warranty as described in the DeWalt literature. BAND-IT does not extend any warranty of any kind to the drill.
Page 14 6. Re-attach drill to tension body making sure the drill and tension body are properly aligned, and tighten the single adapter cap screw located on the aluminum collar.  7. This tool is not designed to work with traditional band and buckle designs. BAND-IT Ultra-Lok clamps must be used.

Band-it Ultra-Lok UL4000 Operating Instructions Manual

Quick Links

Table of Contents

Related Manuals for Band-it Ultra-Lok UL4000

Summary of Contents for Band-it Ultra-Lok UL4000

Table of Contents