Advertisement
10. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result
in a risk of fire and electric shock. If an extension cord must be used, make sure: a) That the pins on the extension
cord plug are properly wired and in good electrical condition: and b) That the extension cord is properly wired and
in good electrical condition: and c) That the wire size is large enough for this power source. For cord length
within 100 feet or less, wire size should be not less than 18 AWG. For cord length within 150 feet or less, wire
size should be not less than 16 AWG.
11. Do not operate the power source with a damaged cord or plug - replace the KMB-27 immediately.
12. Do not operate the power source if it has received a potentially damaging sharp blow, has been dropped, or has
otherwise been damaged in any way: Take it to a qualified serviceman.
13. Do not disassemble the power source, or any Kenwood adapters or accessories. Take it to a qualified serviceman
when service or repair is required. Incorrect re-assembly may result in the risk of electric shock or fire.
14. To reduce the risk of electric shock, unplug the power source from the AC power outlet before attempting any
maintenance or cleaning. Turning off controls will not reduce the risk of shock or fire; the plug must be removed
from the AC outlet.
1. INSTALLATION & OPERATION
The following explicit definitions apply in this manual:
WARNING. Do not disregard. Personal injury may occur.
CAUTION: Do not disregard. Equipment damage may occur.
NOTE: Inconvenience only if disregarded. No risk of equipment damage or personal injury.
FCC Part 15 Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation
SUPPLIED ITEMS:
Locking Bar "A" for KSC-28 (larger bar)
Locking Bar "B" for KSC-37 (smaller bar)
2 Black Phillips #6-32 x lA" Machine Screws (For joining two or more KMB-27).
2 Black Phillips #6-32 x 3/8" Machine Screws (For Locking Bar).
Kenwood KMB-27 Instructions (warranty card not required)
COMBINING TWO CHARGER ADAPTORS
Two or more KMB-27 power sources can be joined side by side to accommodate several sets of radios. Captive nuts
are on the right side (facing) and matching holes are on the left side of the KMB-27. Two extra black machine screws
are provided to attach a second KMB-27. Attach the KMB-27 units BEFORE installing chargers.
ASSEMBLY
1. Optional; 2 units may be fastened side-by-side using 2 supplied black Phillips screws. Join the units before
installing charger cups. Captive nuts are on the chassis sidewall right side (facing), & matching screw holes are on the
left side.
2. Do not connect the AC line cord until after all chargers are installed, and the charger-locking bar is secured in
position. Install up to six Kenwood KSC-28 OR KSC-37 chargers (do not mix chargers).
a)
Unpack the charger cups (transformers will not be used) from each radio carton.
b) Install three chargers in the front row & three chargers in the top rear row with a DC power cord plugged
in completely into each charger base. Slide the front edge of the bottom chargers under the KMB-27
front sloping edge.
c) Lock the chargers in place with either larger locking bar "A" (KSC-28), or smaller bar "B" (KSC-37)
using the 2 supplied black Phillips machine screws. Be careful not to pinch any DC power cords when
the bar is installed. (Store the unused locking bar for possible future use.)
3. Remove all packing material before operation. Do not block the vents.
4. Do not operate in or expose the KMB-27 power source to direct sunlight, heat, dampness, or precipitation.
5. Do not drop or insert conductive material, or any material, into the ventilation slots.
6. NOTE: Fully loaded with chargers, radios & batteries, the KMB-27 weighs up to approximately 8 pounds (3.6kg).
7. Desk- top location: LIFT, DO NOT DRAG. The KMB-27 weighs approximately 8 pounds (3.6kg) fully loaded.
Skid marks may be left on the desk- top.
KMB-27 Instructions V2.6
Advertisement
