Interior Light; Light Tube Replacement; Operating Instructions - Viking 24” Use & Installation Instructions Manual

OPERATING INSTRUCTIONS

S S e e t t t t i i n n g g t t h h e e C C o o n n t t r r o o l l s s
The total available temperature range of the unit is from 40 - 43
18.9 C). The middle range on the control is approximately 55
0
selected, the cooler temperature within the unit. As with any refrigeration product, there is a slight
temperature variance at different locations within the cabinet. For example, the coolest bottles will
be in the rear of the four middle shelves. The bottles on the top two shelves will be 3 - 7
This is the warmest location. The bottles on the front of the middle four shelves will be 1 - 4
than the rear of the shelves. Position your wine inventory accordingly (i.e. white wines in the cooler zones and red wines in the
warmer zones.) To start your wine cellar, use a screw driver to turn the control clockwise to the middle thermostat setting.
Once the bottles are loaded, allow at least 48 hours for the unit to stabilize before making any adjustments to the initial setting.
G G e e n n e e r r a a l l T T i i p p s s a a n n d d S S u u g g g g e e s s t t i i o o n n s s
•After making a temperature adjustment, allow 24 hours for your wine cellar to reach a new temperature setting.
•The motor will start and stop often. It must do this to maintain the temperature setting.
•Unplug the wine cellar before working on anything with the electrical system.
•Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grill and/or the
light fixture switch can occur.

INTERIOR LIGHT

The interior light allows you to view the unit's contents. When the switch is in the "OFF" position, the light
will come on only when the door is opened. In the "ON" position, the light remains on continuously.
DANGER

LIGHT TUBE REPLACEMENT

N N o o t t e e : : Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only approved
replacement light tubes from your dealer or manufacturer.
This product uses two 6-watt light tubes to illuminate the interior
of the wine cellar. The light tubes are very reliable electrical
components, but should either or both light tubes not function
properly, please call your local dealer for replacement light tubes.
To replace the light tube:
•Use a small Phillips head screwdriver to remove the two screws
holding the cover plate over the back section of the light tube.
Set the screws and cover plate aside for re-assembly later.
•Using a small flat-blade screwdriver, gently lever the front section
of the light tube down to allow it to be pulled clear of the light
housing. Disconnect the two insulated electrical connectors from
the cabinet's electrical cable and discard the old light tube.
•Reconnect the insulated electrical connector of the new light tube
to the cabinet's electrical cable connectors. Make sure they are
secure and fully inserted.
•Carefully realign the light tube's electrical terminals back into the rear of
the light enclosure channel making sure not to crimp them. Gently insert the
light tube along the length of the light enclosure channel. Press the light tube
gently into the light enclosure channel. Only a small part of the light tube should project below the ceiling of the
wine cellar. DO NOT USE A HAMMER TO FIT THE LIGHT TUBE.
•Place the light tube terminal cover plate back in its original position on the light enclosure's flange. Re-use the
original two screws to secure the cover in place. Plug the wine cellar into the electrical socket. Check to see if the
light tubes operate properly.
Failure to disconnect the power cord when changing the light tube may result in electrical
shock.
0 F (4.4 - - 6.1 0 C) to 64 - 66
F (12.8 C). The higher the number
0 o
13
0 F (17.8 -
o F warmer.
o F warmer
Light tube
Connectors
Cover plate
Screws