Klutch 144348 Instruction Manual
  1. Manuals
  2. Brands
  3. Klutch Manuals
  4. Drill
  5. 144348
  6. Instruction manual
Klutch 144348 Instruction Manual

Klutch 144348 Instruction Manual

Compact right angle drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Compact Right
Angle Drill
INSTRUCTION MANUAL
WARNING:
Read carefully and understand all INSTRUCTIONS before
operating. Failure to follow the safety rules and other basic
safety precautions may result in serious personal injury.
Item # 144348

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 144348 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Klutch 144348

Summary of Contents for Klutch 144348

  • Page 1 Compact Right Angle Drill INSTRUCTION MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item # 144348...

  • Page 2: General Safety Rules

    Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner's record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.

  • Page 3: Electrical Safety

    • Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY WARNING! Always check to ensure the power supply corresponds to the voltage on the rating plate. • Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances.
  • Page 4 • Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. • Use safety equipment. Always wear eye protection. Nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

  • Page 5: Grounded Tools: Tools With Three-Prong Plugs

    GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of elec- tric shock. Check with a qualified electrician if you are in doubt as to whether the out- let is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug.

  • Page 6: Specific Safety Rules

    RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NAMEPLATE EXTENSION CORD LENGTH AMPERES (At Full Load) FEET FEET FEET FEET FEET 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0 16.1-20.0 *Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE B SPECIFIC SAFETY RULES 1.

  • Page 7: Assembly And Operating

    13. Never use your body to brace the drill. Never put your hands, or other body parts, between the part of the drill being braced and the object it is being braced against. Hands, or other body parts, that are in the direct path of a twisting reaction can be pinched, crushed and broken.
  • Page 8 To Install Drill Bits: WARNING! Always make sure the power switch (69) of the drill is in its “OFF” position and that the tool is unplugged from its electrical outlet before installing drill bits. 2. Insert the chuck key (24) into the chuck (43), and turn the chuck key counter clockwise to open the jaws of the chuck (43) wide enough to insert the drill bit.
  • Page 9 The Power Switch/Reversing Switch: 1. To turn on the drill, squeeze the power switch (69) which is located on the left rear handle (68). To turn off the drill, release pressure on the power switch. 2. The reversing switch (69) is located below the power switch, and is used to remove stuck drill bits from holes.

  • Page 10: Maintenance

    MAINTENANCE WARNING! Always make sure the power switch (69) is in its “OFF” position, and disconnect the drill from its electrical outlet before performing any inspection, maintenance, or cleaning. • Before each use, inspect the general condition of the drill. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged power cord (74), loose, dull, or bent drill bits, and any other condition that may affect the safe operation of the drill.

  • Page 11: Diagram & Parts List

    DIAGRAM & PARTS LIST 64 65 72 26 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
  • Page 12 - f l n i l n i l c t i c t i c t i...
  • Page 13 WARRANTY One-year Limited Warranty Distributed by Northern Tool & Equipment Co., Inc. Burnsville, MN 55306 NorthernTool.com Made in China...

Table of Contents