Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.v Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Contents Introduction What's in the package Features Front/Top Panel Rear Panel Side Panel Mac driver installation Software control panel (Mac) 8-10 Windows driver installation Software Control Panel ( Windows) Software Control Panel (Continues) 12-13 Hardware Connections (Stand-alone unit) Hardware Connections (Use with Qcon control surface) Minimum System Requirements Specifications Services...
In these pages, you'll find a detailed description of the features of the Umix 1008 Satellite digital audio interfaces, as well as a guided tour through their front and rear panels, step-by-step instructions for their setup and use, and full specifications.
Features The ICON Umix 1008 Satellite USB recording interface provides an audio input and output module with USB connectivity. Main features include: Use as a stand-alone unit or plug-in unit to Qcon series MIDI control surface. 24-Bit 96/192KHz 10-In/8-Out USB Recording Interface...
Front/Top Panel “Mic/Inst” inputs 1-8 Unbalanced instrument and balanced mic level inputs. These hybrid connectors will accept a standard 3-pin XLR plug or a 1/4” TS connector. 48V phantom power switch Press to supply +48V phantom power to the associated XLR input. This phantom power circuit is suitable for most condenser microphones.
12V/3A power adaptor (optional) Connect the provided power adaptor here. (Note: Umix 1008 Satellite is not able to work without the provided power adaptor connected. The USB bus power is not able to provide sufficient power supply for Umix 1008 Satellite.)
Driver CD into your CD-Rom, a pop- up window should appear as shown in Diagram 1, then click on the "Mac” folder to open the installation files list. Click “ICON USB Audio.mpkg” Diagram 2 Welcome Screen appears Choose "Continue" when you see...
Page 9
Open the “Audio MIDI setup” window and check if the Umix 1008 Satellite device has setup properly as shown below in diagram 9. If your Umix 1008 Satellite device does not appear on the system settings.It means the driver did not install properly, go through the “Driver Installation”...
Software control panel The “Playback” and “Monitor” mixers work like a matrix mixer. Activate and adjust the correspondence input or output channel level. They are very useful and make your inputs and outputs very flexible. You may route any of your inputs to any outputs.
Please follow the step-by-step procedures below to install your Umix 1008 Satellite USB recording interface and its driver. Turn on your computer Note: Do not connect the Umix 1008 Satellite digital audio interface to your computer yet Insert the Driver CD into your CD-Rom.
Page 12
A window as shown in Diagram 7 should appear. Choose "Install this driver software anyway" Note: Although this message appears, the Umix 1008 Satellite driver is fully tested and supports Windows XP, Vista & Windows 7 Diagram 7 Setup completed A window as shown in Diagram 8 should appear.
Page 13
Diagram 11 Launch the software control panel You may click the Umix1008 logo on the system tray to launch the software control panel (Page 11). Diagram 12 Note: For the latest driver updates please check www.icon-global.com...
It means your computer performance is not able to handle the task. (It is not caused by the Umix 1008 Satellite digital audio interface) Diagram 2 Device settings Shows the serial number & product ID of your Umix 1008 Satellite device.
Hardware Connections (Stand-alone unit) Connect the Umix 1008 satellite digital audio interface outputs to your amplifier, powered monitors or surround system. Two-channel stereo operation, the default outputs are channels 1 and 2. If you are monitoring through headphones, connect your headphones to the device's headphone output.
Satellite connectors located on its side panel. Install the supplied extra back panel to the Umix 1008 Satellite and install the whole unit back to Qcon's rear slot. Connect the Umix 1008 satellite digital audio interface outputs to your amplifier, powered monitors or surround system.
Important: The Umix 1008 Satellite digital audio interface is supported by Mac OS (Intel-Mac), Windows XP, Windows Vista and Windows 7 (32-bit/64-bit). The Umix 1008 Satellite digital audio interface is not supported by Windows 98 or Windows Me. For Windows XP, you must be running SP1 or later. Visit the Windows update web pages to make sure you have the most current updates and fixes supplied by Microsoft.
Services If your Umix 1008 Satellite audio interface needs servicing, follow these instructions. 1. Ensure the problem is not related to operation error or external system devices. 2. Keep this owner's manual. We don't need it to repair the unit.
Need help?
Do you have a question about the Umix 1008 Satellite and is the answer not in the manual?
Questions and answers