Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ICON Satellite UMIX1008
Summary of Contents for ICON Satellite UMIX1008
- Page 1 24-Bit 96/192KHz 10-In/8-Out USB Recording Interface N1630...
- Page 2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.v Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Page 3: Table Of Contents
Contents Introduction What's in the package Features Front/Top Panel Rear Panel Side Panel Mac driver installation Software control panel (Mac) 8-10 Windows driver installation Software Control Panel ( Windows) Software Control Panel (Continues) 12-13 Hardware Connections (Stand-alone unit) Hardware Connections (Use with Qcon control surface) Minimum System Requirements Specifications Services... -
Page 4: Introduction
And so we can send you updated information about these and other ICON products in the future. As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event the product must be returned for servicing, the original packaging (or reasonable equivalent) is required. -
Page 5: Features
Features The ICON Umix 1008 Satellite USB recording interface provides an audio input and output module with USB connectivity. Main features include: Use as a stand-alone unit or plug-in unit to Qcon series MIDI control surface. 24-Bit 96/192KHz 10-In/8-Out USB Recording Interface... -
Page 6: Front/Top Panel
Front/Top Panel “Mic/Inst” inputs 1-8 Unbalanced instrument and balanced mic level inputs. These hybrid connectors will accept a standard 3-pin XLR plug or a 1/4” TS connector. 48V phantom power switch Press to supply +48V phantom power to the associated XLR input. This phantom power circuit is suitable for most condenser microphones. -
Page 7: Rear Panel
Rear Panel Line inputs 1-8 These are balanced analog inputs on standard 1/4″ TS connectors at –10dB line level. Line outputs 1-6 These are balanced analog outputs on standard 1/4″ TS connectors at +6dBU line level. S/PDIF coaxial I/O connectors S/PDIF digital input and output on coaxial RCA connectors. -
Page 8: Mac Driver Installation
Driver CD into your CD-Rom, a pop- up window should appear as shown in Diagram 1, then click on the "Mac” folder to open the installation files list. Click “ICON USB Audio.mpkg” Diagram 2 Welcome Screen appears Choose "Continue" when you see... - Page 9 Open the previous “Mac” folder. Copy the ‘Umix1008” software panel shortcut logo and paste it to your desktop. Icon Control Panel Diagram 7 Launch the software control panel Click the Umix1008's software control panel shortcut logo you have just copied to your desktop to launch the software control panel.
-
Page 10: Software Control Panel (Mac)
Software control panel The “Playback” and “Monitor” mixers work like a matrix mixer. Activate and adjust the correspondence input or output channel level. They are very useful and make your inputs and outputs very flexible. You may route any of your inputs to any outputs. -
Page 11: Windows Driver Installation
Windows driver installation Please follow the step-by-step procedures below to install your Umix 1008 Satellite USB recording interface and its driver. Turn on your computer Note: Do not connect the Umix 1008 Satellite digital audio interface to your computer yet Insert the Driver CD into your CD-Rom. - Page 12 Windows driver installation Driver setup Choose the location of the driver and click "Next" as shown in Diagram 5 Diagram 5 Installation start The installation process has started, the process may take some time depending on your computer performance, please be patient and wait for the process to finish.
- Page 13 Diagram 11 Launch the software control panel You may click the Umix1008 logo on the system tray to launch the software control panel (Page 11). Diagram 12 Note: For the latest driver updates please check www.icon-global.com...
-
Page 14: Software Control Panel ( Windows)
Software Control Panel Sample rate settings Select your desired sampling rate from 44.1KHz to 192KHz on the pull down window shown on Diagram 1. Click "Apply" after the selection has been made to set the value. Diagram 1 Buffer Size settings You may select the buffer size for "Streaming"... -
Page 15: Software Control Panel (Continues)
Software Control Panel (Continues) Monitor Mixer Matrix Fader Hardware inputs level metering Ch 1-8 & S/PDIF input level metering Showing the input level for the hardware input channel. Hardware outputs level metering Ch 1-6 & S/PDIF output level metering Showing the output level for the hardware output channel. Virtual inputs level metering Virtual1-8 input level metering Showing the input level for the virtual input channel. - Page 16 Playback Mixer Matrix Fader Software outputs level metering Ch 1-6 & S/PDIF output level metering Showing the input level for the software input channel. Hardware outputs level metering Ch 1-6 & S/PDIF output level metering Showing the output level for the hardware output channel. Virtual inputs level metering Virtual1-8 input level metering Showing the input level for the virtual input channel.
-
Page 17: Hardware Connections (Stand-Alone Unit)
Hardware Connections (Stand-alone unit) Connect the Umix 1008 satellite digital audio interface outputs to your amplifier, powered monitors or surround system. Two-channel stereo operation, the default outputs are channels 1 and 2. If you are monitoring through headphones, connect your headphones to the device's headphone output. -
Page 18: Hardware Connections (Use With Qcon Control Surface)
Hardware Connections (Use with Qcon control surface) Remove the Qcon's rear panel. Connect the two separate cables to the Umix 1008 Satellite connectors located on its side panel. Install the supplied extra back panel to the Umix 1008 Satellite and install the whole unit back to Qcon's rear slot. Connect the Umix 1008 satellite digital audio interface outputs to your amplifier, powered monitors or surround system. -
Page 19: Minimum System Requirements
Minimum System Requirements Important: The Umix 1008 Satellite digital audio interface is supported by Mac OS (Intel-Mac), Windows XP, Windows Vista and Windows 7 (32-bit/64-bit). The Umix 1008 Satellite digital audio interface is not supported by Windows 98 or Windows Me. For Windows XP, you must be running SP1 or later. Visit the Windows update web pages to make sure you have the most current updates and fixes supplied by Microsoft. -
Page 20: Specifications
Specifications Weight: 1.9kg (4.2lb) Dimensions: 360(L) X 149(W) X 72(H) 14.2”(L) x 5.9”(W) x 2.8”(H) Mic/Inst 1-8 Inputs (Balanced; at Minimum Gain): Frequency Response: 22Hz to 22kHz (+/-0.1dB) Dynamic Range: 100dB, A-weighted Signal-to-Noise Ratio: -100dB, A-weighted THD+N: <0.0048% (-90dB) Crosstalk: -100dB @ 1kHz Input Impedance: Inst in: 390K Ohms, typical;... -
Page 21: Services
If you have lost the packaging, please make sure you have packed the unit properly. ICON is not responsible for any damage that occurs due to non-factory packing. 4. Ship to the ICON tech support center or the local return authorization. U.S. OFFICE: ICON Digital Corporation 8001 Terrace Ave., Suite 201... - Page 22 UM1008S PD3V300-E...
Need help?
Do you have a question about the Satellite UMIX1008 and is the answer not in the manual?
Questions and answers