Toshiba SD5300KC Owner's Manual page 19

Press  /  to select an item, then press  to
C
access.
Example: { Video Out }
The options for the selected item appears.
If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
Use  /  to select a setting and press OK to
D
confirm.
Example: { P-Scan }
The setting is selected and setup is completed.
To exit, press SETUP.
E
Aspect Ratio
The picture shape can be adjusted to fit your TV and
the format must be available on the playback disc.
Otherwise, the TV display will not affect the picture
during playback.
In ' Video ', press  /  to select {Aspect Ratio },
A
then press .
{ 4:3 }
Select this if you have a normal TV. A 'wide-screen'
source display with black bars on the top and bottom
will be displayed on the TV screen.
{ 16:9 }
Select this for wide-screen TV (frame ratio 16:9).
Use  /  to select a setting and press OK to
B
confirm.
View Mode
Use view mode to scale an image that fits to the TV
screen's width and height.
In ' Video ', press  /  to select { View Mode },
A
then press .
{ Fill }
Fill the screen with decoded image.
{ Original }
Display image as its original size.
{ Height Fit }
Fit the screen height with image height.
{ Width Fit }
Fit the screen width with image width.
{ Auto Fit }
Automatically display the decoded image on screen
at a suitable size.
{ Pan Scan }
Automatically display decoded image on full screen
without distortion.
Use  /  to select a setting and press OK to
B
confirm.
Tip:
-Depending on the type of disc, you may not be able
to view the mode as selected.
Video Out
The video output of the DVD player can be selected
as " Component ", "P-Scan" or " HDMI ".
In ＇Video＇, press  /  to select { Video Out },
A
then press .
{ Component }
Select this for Video(CVBS) or component video
connection.
{ P-Scan }
Helpful hint: Press  to go back to previous menu item.
Press SETUP to exit the menu item.
DVD Menu Options
Select this when you connect your DVD player to
your TV, which has component video inputs that
supports progressive scan.
{ HDMI }
Select this for HDMI output.
Use  /  to select a setting and press OK to
B
confirm.
 If the progressive scan feature is activated but
the connected TV does not support progressive
scan, press number button "1" with the disc tray
opened to set the video output of the DVD player to
"Component".
 When Component and HDMI cables are connected
at the same time, and "HDMI" is selected as the TV
Video-In channel for the TV, "HDMI" will be the output
of the DVD player. You cannot switch to "Component"
and "P-Scan".
 When "Component" is selected as the TV Video-In
channel on TV, only "Component" or "P-Scan" option
can be selected as the output of the DVD player.
Smart Picture
This DVD player provides four predefined sets of
picture color settings.
In ' Video ', press  /  to select {Smart Picture },
A
then press .
{ Standard }
Select this for a preset standard picture setting.
{ Vivid }
Select this to make the picture brighter.
{ Cool }
Select this to make the picture softer.
{ Personal }
Select this to personalize your picture color by
adjusting the brightness, contrast, tint and color
(saturation).
Use  /  to select a setting and press OK to
B
confirm.
If you select { Personal }, then proceed to steps
C
D~G.
The setup menu appears.
0
Brightness
0
Contrast
0
Tint
0
Color
Close
Press  /  to highlight one of the following options.
D
Brightness
Increase the value to brighten the picture or vice
versa. Choose zero (0) for average setting.
Contrast
Increase the value to sharpen the picture or vice
versa. Choose zero (0) to balance the contrast.
Tint
Increase the value to darken the picture or vice
versa. Choose zero (0) for average setting.
Color
Increase the value to enhance the color in your
picture or vice versa. Choose zero (0) to balance the
color.
Press  /  to adjust the setting that best suits
E
your personal preference.
Repeat steps D~ to adjust your picture
F E