Getting Started; Inserting Batteries; Finding Your Viewing Channel; Setting Up Progressive Scan Feature - Toshiba SD5300KC Owner's Manual

Getting Started

Inserting Batteries

Open the battery compartment.
A
Insert two batteries type R03 or AAA, following the
B
indications (+ / - ) inside the compartment.
Close the cover.
C
CAUTION:
Never throw batteries into a fire.
Note:
- Be sure to use AAA size batteries.
- Dispose of batteries in a designated disposal area.
- Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
- If the remote control does not operate correctly, or if
the operating range becomes reduced, replace batteries
with new ones.
- When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries
in combination.
- Always remove batteries from remote control if they
are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid
from leaking into the battery compartment.
Using the Remote Control to Operate
the System
30
Within about 6m (19 feet)
OPEN/CLOSE DISPLAY
1 2
4 5
7 8
Aim the Remote Control directly at the remote sensor
A
+10 0
(IR) on the front panel.
MENU
OK
Do not put any objects between the Remote Control
RETURN
B
F.R F.F PREV
PLAY/PAUSE
STEP
and DVD Player while operating the DVD Player.
REPEAT A-B SLOW
SUBTITLE ANGLE AUDIO
RANDOM PROG

Finding your viewing channel

S E -R 0268
Press I/2ON/STANDBY on the DVD player to turn it
A
on.
Turn on the TV and set it to the correct video-in
B
channel. You should see the blue DVD background
screen.
Usually these channels are between the lowest
Helpful hint: Press  to go back to previous menu item.

30
ON/STANDBY
3
6
9
T-SEARCH
SETUP
TITLE
NEXT
STOP
CLEAR
ZOOM
Press SETUP to exit the menu item.
and highest channels and may be called FRONT,
A/V IN or VIDEO. See your TV' s manual for more
details.
Or, you may go to channel 1 on your TV, then
press the Channel down button repeatedly until you
see the Video In channel.
Or, the TV remote control may have a button that
chooses different video modes.
Or, set the TV to channel 3 or 4 if you are using an
RF modulator.
If you are using external equipment, (such as
C
audio system or receiver), turn it on and select the
appropriate input source for the DVD player output.
Refer to the equipment user's manual for detail.

Setting up Progressive Scan feature

(For Progressive Scan TV only)
The progressive scan display twice the number
of frames per seconds than interlaced scanning
(ordinary normal TV system). With nearly double
the number of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
-Ensure that you have connected this DVD player
to a progressive scan TV using the Y, P
connection (see page 6).
-Ensure that you have completed the basic
installation and set up.
Turn on your TV and select the video input
A
connected to the DVD player (refer to your TV user
manual).
Press 2ON/STANDBY on the remote control to turn
B
on the DVD player.
The blue DVD background screen will appear on
the TV.
Press SETUP.
C
Press / to select { Video }, then press .
D
Aspect Ratio Aspect Ratio
Language
View Mode View Mode
Video Out
Video
Smart Picture
HD Resolution
Audio
JPEG Interval
Rating
Misc
Press / to select { Video Out }, then press .
E
Select { P-Scan }, then press OK to confirm.
F
The menu will appear on the TV.
Video Out
Activating Progressive Scan 1. Ensure
your TV supports Progressive Mode
2. If there is a distorted picture on the
TV, wait 15 seconds for automatic
recover
Yes
Press  to highlight { Yes } and press OK to confirm.
G
 The reconfirmation menu will appear on the TV.
P
B, R
: 16:9
: Auto Fit Auto Fit
Component
P-Scan
HDMI
: 5 Seconds
No