Download Print this page
Oster 10-76010 Instruction Manual

Oster 10-76010 Instruction Manual

Heavy-duty detachable blade clipper
Hide thumbs Also See for 10-76010:

Advertisement

Quick Links

Heavy-Duty Detachable
Blade Clipper
Instruction Manual
For Commercial Use Only
Model 10 - 76010
10-76010_12EM1.indd 1
IMPORTANT SAFEGUARDS
Commercial Clipper • When using an electrical appliance, basic precautions
should always be followed, including the following:
Read all instructions before using this appliance.
DANGER
4. Never operate this appliance if it has
a damaged cord or plug, if it is not
working properly, if it has been dropped
To reduce the risk of electric shock:
or damaged, or dropped into water.
1. Do not reach for an appliance that has
Return the appliance to a service center
fallen into water. Unplug immediately.
for examination and repair.
2. Do not use while bathing or in a
5. Keep cord away from heated surfaces.
shower.
6. Never operate the appliance when air
3. Do not place or store appliance where
openings are blocked or while on a soft
it can fall or be pulled into a tub or
surface (such as a bed or couch).
sink.
7. Never drop or insert any object into
4. Do not place in or drop into water
opening.
or other liquid.
8. Do not use outdoors or operate where
5. Always unplug this appliance from
aerosol spray products are being used
the electrical outlet immediately after
or where oxygen is being administered.
using.
9. Do not use this appliance with a
6. Unplug this appliance before cleaning,
damaged or broken comb or blade,
putting on or taking off parts.
as cut or scratched skin may occur.
10. To disconnect, move all controls to
WARNING
"OFF", then remove plug from outlet.
11. Do not wrap cord around unit when
To reduce the risk of burns, fire,
storing. Continuous stress on the
electric shock, or injury to persons:
cord can damage cord insulation and
result in a shock hazard.
1. An appliance should never be left
12. Avoid contact with moving blades.
unattended when it is plugged in.
13. Avoid tangling or kinking the cord
2. Close supervision is necessary when
while clipping. Should the cord become
this appliance is used by, on, or near
tangled or kinked, stop clipping and
children or invalids.
straighten the cord.
3. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
SAVE THESE INSTRUCTIONS
THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY
To reduce the risk of electrical shock, this appliance has a polarized plug
(one blade is wider than the other). This plug fits a polarized outlet only one
way. This is a safety feature intended to help reduce the risk of electrical
shock. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature.
ABOUT YOUR CLIPPER
Although your clipper has been thoroughly tested and inspected at every
stage of its manufacturing and assembly, it is recommended that you lubri-
cate it, as instructed in this manual, after 4-6 weeks of extensive use. This
will ensure you obtain optimum performance and prolong the life of your
clipper.
GETTING FAMILIAR WITH
YOUR CLIPPER
Due to continuous product improvement, product may vary slightly from
what is illustrated.
1. Blade guard
2. Blade
3. Blade bracket
4. Blade hinge
5. Name plate/gear drive assembly access
6. Carbon brush cap/carbon brush
7. Oiler
8. Power cord
9. On/Off switch
10. Hanging ring
11. Cleaning Brush
12. Oster
®
Clipper & Blade Lube™ oil
13. Oster Gear Lube
®
grease
1
11
2
3/4
5
4
12
6
6
6
13
10
9
8
AVAILABLE OSTER
LUBRICANTS & CLEANERS,
®
& REPLACEMENT PARTS
Important:
Regular use of the following products will help you enjoy optimum performance from your
clipper and prolong its functionality.
1. Plug unit into an AC electrical outlet.
2. Move On/Off switch to turn clipper on.
3. Remove blade guard.
4. Insert blade. Holding blade sides, slide blade bracket into hinge.
5. Push blade toward the clipper until it snaps into place
Oster 5-in-1
®
Kool Lube
®
3
Spray
Blade Wash
®
(076300-107)
76300-101
Disinfectant
Cleaning
Lubricates and
All-purpose clipper
76300-102
Solution 76300-
cools down blade.
& blade lubricant
Minimizes bacteria
103
and disinfectant.
buildup between
Flushes away
upper and lower
accumulated hair
blades.
and removes dirt
buildup trapped
between upper
6. When finished clipping, turn clipper off and unplug cord from electrical outlet.
and lower cutting
7. Cover blade with blade guard to keep it protected.
blades.
Note: Any other maintenance not explained in this manual must be per-
formed by an Oster-Direct
Important: Make sure clipper is turned off and unplugged from electrical
outlet before removing, replacing or cleaning any parts.
Lubricating Motor
If you hear a "squeal" or a dry bearing noise
Blade Lube™
Gear Lube
®
Replacement carbon brushes
from the motor, it is a signal that the motor
Oil 76300-104
(076300-105)
(076917-710)
needs lubricating.
Lubricates between
Specially designed
Set of replacement carbon brushes and
Remove cap from Oster
upper and lower
to prolong the life of
springs
Lube™ tube and insert tip into oiler to apply 1
blades to keep
gears, bearings and
drop of oil. Be careful not to over lubricate.
them sharper lon-
the motor.
Greasing Gear Drive Assembly
ger and produce a
smoother clipping
We recommend checking the gear drive
action
assembly every six months for greasing.
Caution: Grease only when necessary as over-greasing may cause
To order any of these products, please call 1-800-830-3678 or visit www.osterstyle.com
leakage and reduce clipper's efficiency.
USING YOUR CLIPPER
Before using your clipper, apply 1 or 2 drops of Oster
®
Clipper & Blade
Lube™ Oil to the blade (refer to Taking Care of Your Clipper section).
For best results, hair should be clean and free from styling agents.
During use, apply Kool Lube
®
coolant occasionally to the blades to keep
them cool.
STEP 4
STEP 5
TAKING CARE OF YOUR CLIPPER
Authorized Service Center.
®
Clipper and Blade
®
APPLY 1
DROP
8/7/12 11:03 AM

Advertisement

loading
Need help?

Need help?

Do you have a question about the 10-76010 and is the answer not in the manual?

Questions and answers

Summary of Contents for Oster 10-76010

  • Page 1 Due to continuous product improvement, product may vary slightly from Read all instructions before using this appliance. Regular use of the following products will help you enjoy optimum performance from your • Before using your clipper, apply 1 or 2 drops of Oster ® Clipper & Blade Blade Clipper what is illustrated.
  • Page 2 When using or cleaning this clipper, do not use any non Oster approved following: negligent use or misuse of the product, use on improper voltage or current, use change the terms and conditions of this warranty. This warranty does not cover...