Remote Control - Pioneer SX-20-K Operating Instructions Manual

03 Controls and displays
Display
1 2 3 4
8
1 H (Headphones)
Lights when both speakers A and B are switched off.
2 RDS indicators
Lights when an RDS broadcast is received.
3 ST
Lights when a stereo FM broadcast is being received in
stereo mode.
4 TUNED
Lights when a normal broadcast channel.
5 Sleep timer indicator
Lights when the receiver is in sleep mode.
6 PRESET
Lights when the tuner preset mode is selected.
7 MEM
Blinks when a radio station is registered.
8 Character display
Displays various system information.
9 kHz/MHz
Lights when the character display is showing the
currently received AM/FM broadcast frequency.
10 Preset information
Shows the preset number of the tuner.
11 DIRECT
Lights when the TONE DIRECT mode is switched on.
8
En

Remote control

5 6 7
STANDBY/ON
1
1 2
9 10 11
2 4 5
7 8
TONE DIRECT 0 SURROUND
3
4
RDS
SEARCH PTY DISPLAY
5
FM MODE P.SCAN
6
7
MEM
8
FM/AM INPUT
SACD/CD NETWORK PHONO
9
BASS
10
NETWORK AUDIO PLAYER
11
SACD PLAYER
SETUP
12
ENTER
HOME MENU RETURN
STEREO RECEIVER
 STANDBY/ON
1
Switches the receiver between standby and on.
2 Numeric buttons (0 ~ 9)
Press to select or to store preset.
SLEEP
3 TONE DIRECT
13
Press to select the TONE DIRECT mode (page 12).
4 SURROUND
Press to select the surround sound options (page 12).
3
APD
14
5 RDS control buttons
6
SEARCH – Use to select the search mode (page 11).
A
15
PTY – Use to search for RDS program types
SPEAKERS
9
(page 11).
B
DISPLAY – Use to display the RDS information
DIMMER (page 11).
16
6 Tuner control buttons
FM MODE – Press to select the desired FM mode
MUTE
(Stereo or monaural) (page 10).
17
P.SCAN – Press to scan the stations in the preset
sequence (page 10).
VOLUME
T/P MODE – Press to select the tuning mode or the
preset mode (page 10).
18 MEM – Press to store preset stations (page 10).
/
7
At the tuning mode, use to find radio frequencies.
At the preset mode, use to select preset radio stations.
Also used when setting up the receiver.
RECORDER
8 BALANCE
TREBLE
When adjusting the sound volume balance, press to
enter the balance mode (page 11).
9 Input function buttons
Press to select an input source. These select the
component connected to the corresponding input on the
FUNC
rear panel.
INPUT – Press repeatedly to select desired input
function. Use to change the input source. The
source changes as below.
SACD/CD  NETWORK  PHONO 
RECORDER  FM/AM  Return to the beginning.
10 Tone control buttons
BASS +/– – Use to adjust Bass (page 11).
TREBLE +/– – Use to adjust Treble (page 11).
11 SACD PLAYER control buttons
Use to control Pioneer SACD/CD player.
12 NETWORK AUDIO PLAYER control
buttons
Use to control Pioneer network audio player.
13 SLEEP
Press to change the amount of time before the receiver
switches into standby (10 min – 20 min – 30 min – 60 min
– 90 min – Off). You can check the remaining sleep time
at any time by pressing SLEEP once.
14 APD
Use to change the Auto Power Down function setting
(page 12).
15 SPEAKERS A/B buttons
These buttons allow you to select various combinations
of speakers as follows:
• To drive A speakers, press SPEAKERS A button
(SPK A is displayed).
• To drive B speakers, press SPEAKERS B button
(SPK B is displayed).
• To drive both A and B speakers, press SPEAKERS A
and B buttons in order (SPK A B is displayed).
• When using headphones for private listening, press
these buttons in order to switch off the speakers A
and B (SPK OFF is displayed, and H indicator
lights).
16 DIMMER
Dims or brightens the display. The brightness can be
controlled in four steps.
17 MUTE
Mutes/unmutes the sound.
18 VOLUME +/–
Use to set the listening volume.