Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for JBL EON10
Summary of Contents for JBL EON10
- Page 1 EON10 G2 User Guide Part Number: 981-00061-01...
-
Page 3: Table Of Contents
ABOUT THE EON10 G2 ........ -
Page 4: Package Contents
EON is a creation of JBL, the world leader in sound reinforcement. JBL sound systems are used in some of the world’s most famous arenas, concert halls and clubs. In fact, JBL speakers are the premier choice for today’s hottest touring acts and artists. You just can’t make a more professional choice. -
Page 5: Care And Maintenance
The EON10 G2 generates considerable energy. When placed on a slippery surface such as polished wood or linoleum, the EON10 G2 may move due to its acoustical energy output. Precautions should be taken to ensure that the speaker does not fall off a stage or table on which it is placed. One solution is to place the speaker on a rubber mat. -
Page 6: About The Eon10 G2
• 1” (throat diameter) JBL compression driver with titanium diaphragm and ferro-fluid cooling. • Bi-amplified 125 watts low frequency and 50 watts high frequency - actual power delivered to the drivers. -
Page 7: Frequency Response
Frequency Reponse Available Accessories SS2-BK Tripod Stand ESK10 Suspension Kit for EON 10” models BRK10 Bracket, adapts EON 10” models to OmniMount EON10 Bag-1 Zippered, plushed-lined speaker bag for EON 10” models Block Diagram ® brackets... -
Page 8: Quickstart
Controls INPUT 1 Adjusts the level of INPUT 1. Use this control to match the input sensitivity of the EON10 G2 to the output level of the mixer, microphone, or instrument connected to INPUT 1. It is a common miscon- ception that this control changes the power of a system. -
Page 9: Switches
The MIC/LINE switch effects only INPUT 1. It selects between two sensitivity ranges. This switch is used to match the input sensitivity of the EON10 G2 with the output level of the device connected to INPUT 1. Depressing the MIC/LINE switch selects MIC (most sensitive) and causes the MIC/LINE LED to illuminate. -
Page 10: Indicators
Your EON10 G2 will typically be set at the factory to accommodate the power mains voltage in your area. Before you set up your EON10 G2 for the first time it is a good idea to verify that the setting of the selector is appropriate for the power in your area. -
Page 11: Application Examples
“insert cable”. Portable CD Player - A portable CD player may be connected to the EON10 G2 by means of a 1/4” TRS to Mini-Phone adapter. Again, the left and right channels will be combined into mono. -
Page 12: Basic Sound Reinforcement System With Stage Monitors
This is the basic live sound system. The optional tripod stands will get the speakers up above the audience so the sound can project. The second pair of EON10 G2 speakers are used as stage monitors. For maximum gain before feedback, position the monitors so that they do not point into microphones. -
Page 13: Dj System With Passive Subwoofers
DJ System with Passive Subwoofers This system combines a pair of EON10 G2 powered speakers with externally powered subwoofers for extra power at very low frequencies. * Recommended crossover frequency = 80-150 Hz. (season to taste) INPUT 1 High Pass Output... -
Page 14: Troubleshooting
Disconnect and re-seat signal cables. Replace suspected cable with a known-good cable. The EON10 G2 does not supply phantom power. Switch to a dynamic microphone, use a battery in the microphone (if possible), use an external phantom power supply. - Page 15 Symptom Likely Cause Hum or Buzz that increases or Improper A/C ground or faulty decreases when the mixer level equipment connected to mixer controls are moved. input. Faulty cable between source equipment and mixer. Hum or Buzz. Improper A/C grounding, ground loops.
-
Page 16: Reference
The input level control simply determines how much input voltage is required to drive the amp to full output. If the input level controls of an EON10 G2 are set too low (rotated too far counter-clockwise) the mixer will go into clipping before the speakers are driven to full output. -
Page 17: Connections - Balanced And Unbalanced
Connections - Balanced and Unbalanced There are two basic types of audio system interconnections for very low to medium level audio signals: Balanced and unbalanced. Your EON10 G2 can accept either type of input. Balanced Lines In audio, a balanced line is a three-conductor system in which the two signal wires carry an equal, but opposite voltage with respect to the ground wire. -
Page 18: Cables And Connectors
• Used to connect outputs of consumer audio products to the unbalanced inputs of many pro-audio devices. • Used to connect headphones with Mini-Phone cables to 1/4” headphone jacks. • Adapts the output of portable audio players and computers to INPUT 2 & 3 on the EON10 G2. - Page 19 XLR/F to XLR/M Microphone Cable TRS (Balanced) 1/4Ó Phone to XLR/M Cable TS (Unbalanced) 1/4Ó Phone to XLR/M Cable XLR/M to RCA (phono) Cable TS (Unbalanced) 1/4Ó Phone to RCA (phono) Cable TRS 1/4Ó Phone to dual TS 1/4Ó Phone TRS 1/8Ó...
-
Page 20: Jbl Limited Warranty & Contact Information
The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the date of original purchase.