1. Manuals
  2. Brands
  3. Magnum Manuals
  4. Amplifier
  5. MD 308
  6. Instruction manual

Magnum MD 308 Instruction Manual

Integrated amplifier
Hide thumbs
Table of Contents

Advertisement

Quick Links

Magnum Dynalab MD 308
INTEGRATED AMPLIFIER
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Magnum MD 308

Summary of Contents for Magnum MD 308

  • Page 1 Magnum Dynalab MD 308 INTEGRATED AMPLIFIER INSTRUCTION MANUAL...

  • Page 2: Table Of Contents

    SETTING UP THE MD 308 CONNECTING SPEAKERS AND POWERING THE MD 308 HOOKING UP SOURCES TO THE MD 308 SET UP THE MD 308 WITH AN EXTERNAL HOME THEATER PROCESSOR HOOKING UP A SUBWOOFER TO YOUR SYSTEM TAPE OUT LOOP POWER VU-METERS CONTROL &...

  • Page 3: A Message From The President

    FM tuner will insure optimum performance. Once again thank you for including a MAGNUM DYNALAB product in your entertainment system, we are sure that you will have years of listening pleasure...

  • Page 4: Unpacking Your Md 308

    Carefully remove the MD 308 from the end caps and wrapping, inspect all sides. Pay special attention to the corresponding areas on the unit where damage was found to the shipping carton.

  • Page 5: Setting Up The Md 308

    AC source that you are using. CONNECTING SPEAKERS AND POWERING THE MD 308 1. Now that you have unpacked and positioned the MD 308 you are ready to hook it up. Hook up your speakers to the receiver insuring that the positive (+) terminal on the speaker is hooked up to the positive (+) output terminal on the receiver, likewise that the negative (-) is correctly hooked up.

  • Page 6: Hooking Up Sources To The Md 308

    To Connect to a Home Theater Processor 1. Turn the power off to the MD 308 by the main power switch on the rear of the unit. 2. Connect your theater processor Main Left and Right interconnects into the MD 308 through the A4 input.

  • Page 7: Hooking Up A Subwoofer To Your System

    6. Input A4 is now the dedicated input for you to listen and control volume with your home theater processor (Meaning that when you listen to regular music you use the preamplifier found in the MD 308). Once input A4 has been activated into Home Theater mode, volume on input A4 will now be controlled via your external processor preamp.

  • Page 8: Control & Display Functions

    Note that the amount of deviation from center balance will be shown in dB on the display. 2. INPUT INDICATOR: When the MD 308 is powered on, this LED will be lit. 3. RIGHT BALANCE INDICATOR: This will light up when you change the output balance of the amplifier.

  • Page 9: Remote Control

    MD-308. The remote has been designed to be compatible not only with the MD- 308, but also with our collection of analog FM tuners. Therefore, this remote will be functional with a Magnum Dynalab tuner should one be added to your home audio system.

  • Page 10: Troubleshooting

    - 10 - TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION • Power cord disconnected • Connect power cord No sound, meter lights • Power off at source • Check AC source are not on • Fuse blown • Check rear panel fuse •...

  • Page 11: Safety Sheet11

    - 11 - SAFETY SHEET IMPORTANT SAFETY INSTRUCTIONS 1. KEEP THESE INSTRUCTIONS 2. HEED ALL WARNINGS 3. FOLLOW ALL INSTRUCTIONS 4. DO NOT USE THIS APPARATUS IN WATER 5. CLEAN ONLY WITH DRY CLOTH 6. DO NOT BLOCK ANY VENTILATION OPENINGS, INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.

  • Page 12: Limited Warranty

    LIMITED WARRANTY Register your product at www.magnumdynalab.com Magnum Dynalab Ltd. herein referred to as the “manufacturer” guarantees this product to be free of defect in both material and workmanship and agrees to remedy any such defect or replace any defective component at no charge for a period of two years from date of sale to the first end user.

Table of Contents