Information - Emerson LC260EM2 Owner's Manual

Symptom
No picture or sound
No color
Adjusted [Picture] or [Sound]
settings are not effective every time
the unit is turned on.
Sound OK, picture poor
Picture OK, sound poor
You see a distorted picture or hear
an unusual sound.
Ghosts, lines or streaks in picture
You see "noise" or "trash" on the
screen.
Different color marks on the TV
screen
You switch to a different input and
the volume changes.
You switch to a different input and
the screen size changes.
The display image does not cover
the entire screen.
Captions are displayed as a white
box. No caption is displayed in
the Closed Caption-supported
program.
Black box is displayed on the TV
screen.
Note
• The LCD screen is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of blue,
green or red.
This is not to be considered a defect in the LCD screen.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this manual for more details on
correct operations.
Remedy
• Check if the power is on.
• Check if the correct input mode is selected.
• Check whether all the cables to the unit are connected to the correct output jack of your device like
Blu-ray / DVD recorder.
• View other TV channels. The problem might be limited to the broadcasting station or weak signal
strength.
• Unplug the AC power cord and wait for about 1 minute, then plug the AC power cord and turn on
the unit again.
• Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.
• Make sure that the selected input mode is connected to the working input jack.
• Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode. Tap
any key on the keyboard to wake up your computer.
• Make sure that the sound is not muted. Press MUTE
level will appear on the TV screen.
• Make sure that the volume is NOT set to [ 0 ] or [Mute]. If so, use VOL
volume.
• View other TV channels. The problem might be limited to the broadcasting station or weak signal
strength.
Adjust [Color] in the main menu.
•
You must set [Home] in [Location].
•
Otherwise, the settings you adjusted will not be memorized after the unit goes into standby mode.
• Electrical interference from nearby appliances may affect picture quality.
Adjust [Contrast] and [Brightness] in the main menu.
•
• View other TV channels. The problem might be limited to the broadcasting station or weak signal
strength.
• For the best picture quality, watch "High Definition" wide screen programs.
If the HD content is not available, watch "Standard Definition" programs instead.
• View other TV channels. The problem might be limited to the broadcasting station or weak signal
strength.
• Check if the audio cable is connected in correctly.
• You may be getting interference from electrical appliances, automobiles, motorcycles or fluorescent
lights.
• Try moving the unit to another location to see if this is the cause of the problem.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station or weak signal
strength.
• When the capabilities of the unit exceed the capabilities of the digital broadcasting, the signal will be
increased to match the capabilities of the display of the unit. This may cause noise or trash.
• View other TV channels. The problem might be limited to the broadcasting station, missing data or
pixelation.
• This unit will memorize the volume level from the last time you adjusted it.
• If the volume of the sound from another device is higher or lower, then the loudness will change.
• This unit will memorize the viewing mode from the last time you used the particular input modes.
• If you are using the unit as a PC monitor, make sure that [Horizontal Position] and [Vertical Position]
in [PC Settings] are set correctly.
• If you are watching TV or using the Composite Video, Component Video or HDMI with 480i Input,
press FORMAT repeatedly to switch various screen modes.
• Interference from buildings or weather conditions may cause captioning to be incomplete.
• Broadcasting station may shorten the program to insert advertisement.
The closed caption decoder cannot read the information of the shortened program.
• The text mode is selected for caption. Select [CC-1], [CC-2], [CC-3], [CC-4] or [Off].
so that the volume bar and current volume
p. 23
➠
29
English
/ to adjust the desired