Download Print this page

GE 45132 User Manual

Wireless alarm system motion sensor.
Hide thumbs

Advertisement

Wireless Alarm System
Motion
Sensor
User's Manual
Choice
Choice
ALERT
ALERT
Control all Sensors
& accessories from
one location
45132

Advertisement

   Related Manuals for GE 45132

   Summary of Contents for GE 45132

  • Page 1

    Wireless Alarm System Motion Sensor User’s Manual Choice Choice ALERT ALERT ™ ™ Control all Sensors & accessories from one location 45132...

  • Page 2: Table Of Contents

    Important Safeguards Introduction Assigning a Sensor to a Zone Testing a Sensor or your system Installation Erasing a Sensor from a Zone Low battery indicator Battery warnings F.A.Q.'S FCC Warning Table of Contents 1-1...

  • Page 3

    Before connecting or operating the Motion Sensor, please read these instructions carefully and save this manual for future reference. Congratulations The GE Choice Alert Wireless Alarm System is one ™ of the most affordable and expandable wireless alarm systems available. You’ll discover the system offers many features typically found in custom installed Alarm systems.

  • Page 4: Important Safeguards

    Important safeguards PreCautions 1. Do not attempt to disassemble the Motion Sensor, unless described in the user’s manual. There are no user serviceable parts. . Handle with Care – Avoid striking or shaking. Improper use or storage could damage the Motion Sensor.

  • Page 5: Introduction

    The Motion Sensor is designed to be used indoors or out. When mounted properly it can monitor large or open areas such as entrances, living rooms, family rooms, driveways, backyards, walkways, workshops, etc. When the Sensor detects motion, it will transmit a signal to the Control Center.

  • Page 6

    The Motion Sensor consists of 2 parts – The Sensor (Transmitter) and the wall mount. Before installing, remove the screw from the battery door on the back of the Sensor. You’ll need to attach the battery leads to a “9V” battery (not included); Take care to note the polarity markings.

  • Page 7: Testing A Sensor Or Your System

    button located inside the battery compartment, or if mounted wave your hand in front of the Sensor (the red LED indicator will flash inside lens area in front of the Motion Sensor). Testing a Sensor or your system Once all the Sensors have been assigned to Zones in the Control Center you can now test your system.

  • Page 8

    Step  - Set the Notification Mode to switch ‘Alert’ position and begin activating Sensors one at a time. Note: The sensor has a LED that flashes to show when the sensor has triggered and transmitted to the main unit. Step 4 - When testing is complete, unplug the AC adapter, then plug the AC adapter back in and reinstall batteries.

  • Page 9: Erasing A Sensor From A Zone

    Note: If you need to remove the Sensor from a Zone, the system will erase the entire Zone, so any other Sensors will need to be put back into that particular Zone. Step 1 - To erase a Zone, press and hold the Learn button on the Control Center.

  • Page 10

    However, you can check the Motion Sensor status independently by placing the Control Center in Test mode (see Testing a Sensor on page 7) and trigger the Sensor separately. If mounted, wave hand in front of Sensor, or press activation button for two seconds inside battery compartment.

  • Page 11: Battery Warnings

    Model # Description 45129 Control Center 45132 MotionSensor *maximum potential life based upon usage and location WARNING! Risk of personal injury - Prolonged exposure to alarm siren may cause permanent hearing loss Battery Warning! - Remove batteries before storing the Alarm or Sensor for extended periods...

  • Page 12

    Motion Sensor F.A.Q.’S Q. I bought a new Sensor and the Control Center will not recognize it. Why? A. First, make sure that the battery is new and has been correctly attached to the terminals. Confirm that the Sensor has been correctly assigned to a Zone. Q.

  • Page 13

    Sensor.This will cause low battery indication on the Control Center (See pg 10). Q. Why does one of my Zones continually flash? A. This can be caused by 1 of 2 conditions. First condition, if it is a rapid flash it means a Sensor in the Zone has a low battery.

  • Page 14: Fcc Warning

    Any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1) The Choice Alert system may not cause harmful interference.

  • Page 15

    The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, JASCO is not an insurer, this product is neither insurance nor a guarantee that such an event will be prevented, and users should protect themselves with proper insurance.

  • Page 16

    General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit 45132-1 www.jascoproducts.com for details. 01/18/08...

This manual also for:

Choice alert 45132

Comments to this Manuals

Symbols: 0
Latest comments: