Contec RT-U46C Programming And Operating Instructions

CheckMate TM III
1. Introduction
CheckMate TM III
Your CheckMate™ III (Model RT-U46C) universal
Model RT-U46C
remote control is simple to program, easy to use, and
Universal Remote Control can operate up to three (3) devices, which include:
CABLE Cable set-top terminals
TV Televisions
VIDEO VCR, DVD
Before you can use your remote control, it must be
programmed (set-up) to operate the above devices.
2. Before Getting Started
Some of the special features and buttons on your
remote control are as follows:
Point and Press TM Programming
Let's you program your TV and VCR devices without
codes. For more information, see sections 5 and 6.
[VCR / VOD] Toggle
"Toggles" the VCR buttons between cable Video-
On-Demand ( VOD ) and VCR / DVD functions. For
more information, see section 13.
Smartkeys TM
Program multiple button presses on the [ CBL ] and
[ TV ] buttons. For more information, see section 8.
Time Out
Shuts off remote if any button is pressed and held
for 45 seconds. This extends battery life in the event
the remote becomes lodges under or between
heavy objects
Reset
Lets you reset your remote to its original default
settings. For more information, see section 11.
[Movies], [Sports], [News]
Program your favorite channels on the "Movies",
"Sports" and "News" buttons. For more information
see section 9.
For Motorola DCT ® or CFT2200 cable set-top
terminals, these buttons are pre-programmed and
labeled [ PPV /LOCK ], [ *HELP ], [ MUSIC ].
3. Installing / Replacing Batteries
Programming And Operating
Install two (2) new "AA" batteries as indicated by the
Instructions
diagram in the battery compartment.
To have a clearer idea of the features and capabilities of
When the indicator light becomes dim or no longer
your remote control, take a moment to read these
instructions. Save for future reference. illuminates during use, install two (2) new "AA" size
batteries.
Rev. 12/2001
© 2001, CONTEC CORPORATION
Your remote control has Memory Guard™, which
eliminates reprogramming after battery changes.
RT-U46C 2 CheckMate TM III RT-U46C
4. Programming Your Cable Set-Top Terminal
Model RT-U46C is pre-programmed to operate the
Scientific-Atlanta Explorer ® , Pioneer Voyager ® and
Pace 510 digital set-top terminals.
To operate a different cable set-top terminal, look up
the brand and model in the Cable Setup Code list. If
you are not sure of your brand and model, contact
your cable company.
To program your cable set-top terminal...
1. Turn on your cable set-top terminal.
2. Press [CBL], then [ SELECT ] together - hold both
buttons down until indicator light illuminates.
3. From the Cable Setup Code list, locate and enter
the 3-digit code for your brand and model.
4. Press [CBL] to lock in the code. The indicator light
will blink and go out.
Write your cable set-top terminal brand & setup
code .
Cable Setup Codes
Motorola (General Instrument)
DCT, CFT 2200
CFT2100, CFT2000
Jerrold
DL4, DP(V), DQN(V), DPBB
Scientific Atlanta
Explorer
Explorer(#, *)
Explorer(Blue Ridge)
Explorer(WorldGate™)
8600X
8600
8540, 70, 90
Pace
510 digital
Philips
digital
Pioneer
Voyager
BC-4600, BA-6000
BA-9000
BA-V1000, BA-V2000
Tocom
5503VIP, 5507, 5508
Zenith
Z-Tac
MM2500
Oak
Sigma One, P1, P2, P3
Sigma 2000
3 CheckMate TM III RT-U46C 4 CheckMate
TV Setup Codes
5. Programming Your TV
Admiral
If you have a TV that's operated by remote control,
Adventura
it is recommended that you plug it directly into a
Akai
wall outlet instead of the cable set-top terminal.
Aiwa
To program your TV... Amark
Ampro
1. Turn on your TV.
Amstrad
2. Press [ TV ], then [ SELECT ] together - hold both
Anam
buttons down until the indicator light illuminates.
AOC
3. a.Press and hold [CH+] until your TV turns off. As Audio Vox
soon as your TV turns off, release [CH+] . Belcor
Bell & Howell
OR
Broksonic
b.From the TV Setup Code list, locate and enter
Brokwood
a 3-digit code for your brand. If multiple codes
Candle
are listed, you may have to enter several 3-
Centurion
digit codes until your TV turns off.
Citizen
Concerto
4. Press [ MUTE ]. If your TV turns back on, press
Contec
[ TV ] to lock in the code. The indicator light will
Coronado
blink and go out.
Craig
If your TV does not turn back on, repeat steps 3
Crown
and 4 until you can turn your TV off and on.
Curtis Mathes
001 Daewoo
Write your TV brand & setup code_____________.
002
Refer to section 10 for code number readback.
003 Daytron
Dumont
Note when using the Point and Press™‚
Electro Home
Programming method (step 3a). If you find a code
004 Elektra
that turns your TV off but not back on (step 4), you
015
Emerson
may have gone past the correct matching code.
016
Try pressing [ CH –] one step at a time until you find
018
Envision
a code that turns your TV back on.
005
Fisher
006
To program your TV / VCR combination unit... Funai
007
GE
1. First, program your remote for the TV functions.
004
Following the steps in this section, find a TV Setup
Gibralta
Code that operates the TV functions of your
Goldstar(LG)
017
TV/VCR (power, vol+/–, mute, ch+/–, 0-9).
Grundig
2. Then, program your remote for the VCR Hall Mark
004
Hitachi
functions.
008
Inkel
009
Following the steps in Section 5 for code number
010 JC Penney
entry, enter, lock and test each 3-digit VCR
JVC
Setup Code until a code is found that operates
011 Kawasho
the VCR functions of your TV / VCR (play, stop,
KMC
fast-forward, rewind, pause, record).
012 KTV
013 Note: You can not use the Point and Press™
Kurazai
Programming method to program the VCR Lodgenet
014
functions of the TV / VCR. Logik
Luxman
TM III RT-U46C 5 CheckMate TM III RT-U46C
LXI 006 035 067
Magnavox(Philips) 001 005 007 014 026 027 041 052 068 081
058 061 062 067
Majestic 062
004
Marantz 003 065 076
065
Megatron 086
135
Memorex 010 031 062
007 086
MGA/Mitsubishi 003 027 031 041 044 051 065 076 084
112
Montgomery Ward 007 037 044 057 058 062 065 067 081
006
NEC 023 027 031 044 101
088 089 093 111 120 125 134
Orion 013 017 033 045 047 078
065
Panasonic 018 019 021 024 053 063
111
Philco 001 007 027 052 065 081
041
Philips(Magnavox) 001 005 007 014 026 027 041 052 068 081
062
Pilot 041 059 097
011 054
Pioneer 056 103
041
Portland 007 027
027 052
ProScan 055 061 073 082 112
044 051
Proton 031 126 128
027 052 059 062
Pulsar 041
041 051
Quasar 019
020
Radio Shack 041
007
Realistic 012 057 079
134
RCA 022 027 046 053 055 061 065 072 073 082
007
Sampo 031 044
044 061 062
Samsung 007 016 020 031 044 119 129
027 039 040 041 042 051 090 091 092 094
Sanyo 002 010 028 104 133
101 102 108 114 118 121 123 130
Scott 031 044 079
041 044 051
Sears 002 007 010 016 027 028 043 069
041
Sharp 007 009 023 035 057 064 067 096
041 051
Signature 2000 007 044 058 062 067
002
Sony 032 038 050 066
007 008 011 012 017 054 065 079 108 110
Soundesign 052
131
Squareview 006
041 051
Supre-Macy 071
010 028
Sylvania 001 005 006 026 027 031 044 052 081 108
004
Symphonic 004 006
005 019 027 031 037 041 046 051 053 055
Tatung 019
061 070 131
Techwood 027
007 025 027 031 041 044 051 059 060 065
Teknika 001 007 027 052 062 079
007 027 031 041 044 059 060 065 124
Telerent 007 062
059
TMK 027 031
041 051
Tera 127
007 027 049 051 083 085 098 100
Toshiba 016 029 043 069
075
Totevision 059
005 010 027 037 041 051 065 069 070
Universal 027 070
048 077 080 132
Vidtech 027
041 051
Wards 027 031
007
White Westinghouse 058
007 030 059 065
XR-1000 062
062
Yamaha 027
062
York 031 044
062
Zenith 004 015 025 034 036
027 041 051
6 CheckMate TM III RT-U46C 7
6. Programming Your VCR or DVD (Video device)
To program your VCR or DVD...
1. Turn on your VCR or DVD.
2. Press [ VIDEO ], then [ SELECT ] together - hold both
buttons down until the indicator light illuminates.
3. a.Press and hold [ CH +] until your VCR or DVD turns
off. As soon as your VCR or DVD turns off,
release [CH+] .
OR
b.From the VCR - DVD Setup Code list, locate and
enter a 3-digit code for your brand. If multiple
codes are listed, you may have to enter several 3-
digit codes until your VCR or DVD turns off.
4. Press [ MUTE ]. If your VCR or DVD turns back on,
press [VIDEO] to lock in the code. The indicator light
will blink and go out.
If your VCR or DVD does not turn back on, repeat
steps 3 and 4 until you can turn your VCR or DVD
off and on.
Write your VCR / DVD brand & setup code ______.
Refer to section 10 for code number readback.
Note when using the Point and Press™‚ Programming
method (step 3a). If you find a code that turns your
VCR / DVD off but not back on (step 4), you may
have gone past the correct matching code. Try
pressing [ CH –] one step at a time until you find a
code that turns your VCR / DVD back on.
VCR Setup Codes
Admiral 014 056
Adventura 025
Aiwa 025 106
Akai 011 021 051 092 098 103
Audio Dynamics 007 044
Bell & Howell 005 024
Broksonic 009 048 053 064
Canon 008 034 105
Citizen 002 006 028 060
Colortyme 044
Craig 028 030
Curtis Mathes 008 013 034 044 060
Daewoo 006 010 012 057 058 112 114 116
Daytron 055 058
DBX 007 044
Dynatech 025 106
Emerson 002 003 006 008 009 022 033 040 049 051
064 091 101 106 107 109
Fisher 005 015 024 030 052
Funai 025 106
GE 008 027 028 034 041
Go Video 019 043 063
Goldstar(LG) 002 060