Electrical Connections - Goodman *MVM96 Installation Instructions Manual

FIELD SUPPLIED HOSE
AND CONNECTORS
NOTE: MAKE SMALL
LOOP IN HOSE TO
SERVE AS "P-TRAP"
NOTE: When using the horizontal alternate vent configuration,
you must use the RF000142 vent drain kit.
1. Remove the rubber plug/cap from the front cover left
(down) side drain port.
2. Relocate the front cover pressure switch hose connection
from the right side (as shipped) pressure tap to the left
(down) side tap. The pressure switch hose must be
connected to the down side to guard against blocked drain
conditions. Cut hose to appropriate length to minimize
sagging. Plug right (unused) pressure tap with plug
removed from left side.
3. Secure Hose A to front cover drain port with a red hose
clamp. Route hose to rear left (down) side panel grommet
holes. NOTE: For left side drainage, grommets must be
relocated to left side panel.
4. Remove the rubber cap from the side drain port on the
rubber elbow.
5. Secure the short end of Hose B to rubber elbow side drain
port using a green hose clamp. NOTE: For left side
drainage, route hose to far left (down) side panel grommet
holes. NOTE: Horizontal left side connections (when using
new side port drain elbow) does not require connecting a
hose to the induced draft blower housing.
6. Cut 5 1/2 inches straight length from the long end of each
Tube 2 and discard radius ends.
7. Insert approximately one inch of each Tube 2 through left
side panel grommet hole. Secure tubes to Hose A and
Hose B with a green hose clamps. NOTE: Tube must
reach bottom of trap. Ensure hoses and tubes maintain a
downward slope for proper drainage and that they are not
kinked or binding.
For details concerning mounting of the drain trap, refer to Con-
densate Drain Lines and Drain Trap - Horizontal Drain Trap Mount-
ing.
H D T M
ORIZONTAL RAIN RAP
P )
ANEL
1. Position the drain trap against side panel with drain tubes
inserted into trap. Note that the trap may be orientated
with the outlet facing either the furnace's top cover or base
pan.
VENT
RF000142 KIT
(L R S
OUNTING EFT OR IGHT
2. Secure drain trap to side panel at the dimples or crosshairs
located on either side of the grommet drain holes.
3. Confirm that tubes reach bottom of drain trap and that all
hoses maintain a downward slope and are not kinked or
binding.
4. Attach PVC drain line to drain trap outlet with either a 90°
elbow or coupling.
FRONT COVER
DRAIN PORT
RED HOSE
CLAMP
HOSE A
HOSE B
TUBES 2
DRAIN TRAP
Allow 4-3/4"
minimum
for trap
Horizontal Connections - Right Side Down
(Upflow Shown, Counterflow Similar)
E
LECTRICAL
HIGH VOLTAGE !
T
O AVOID THE
THE UNIT MUST
HIGH VOLTAGE !
T
O AVOID PERSONAL
ELECTRICAL SHOCK
BEFORE SERVICING
.
WIRING
L
ABEL ALL WIRES
. W
CONTROLS
. V
OPERATION
IDE
27
PRESSURE
GREEN
HOSE
TUBE 1
CLAMP
(3 PLACES)
C
ONNECTIONS
WARNING
,
RISK OF ELECTRICAL SHOCK WIRING
BE POLARIZED AND GROUNDED
WARNING
INJURY OR DEATH DUE TO
,
DISCONNECT ELECTRICAL POWER
OR CHANGING ANY ELECTRICAL
CAUTION
PRIOR TO DISCONNECTION WHEN
IRING ERRORS CAN CAUSE IMPROPER
ERIFY PROPER OPERATION AFTER
FRONT
COVER
RUBBER
TAP
ELBOW
RIGHT
SIDE
PANEL
RUBBER ELBOW
DRAIN PORT
SILVER HOSE
CLAMP
TO
.
SERVICING
AND DANGEROUS
.
SERVICING