HISTORY INFORMATION FOR THE FOLLOWING MANUAL: LA-4 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDF-46E2000 RM-YD010 US/CND KDF-46E2010 RM-YD010 MEXICO KDF-50E2000 RM-YD010 US/CND KDF-50E2010 RM-YD010 MEXICO KDF-55E2000 RM-YD010 US/CND KDF-55E2010 RM-YD010 MEXICO ORIGINAL MANUAL ISSUE DATE: 5/2006 :UPDATED ITEM...
Page 2
Self Diagnosis Supported model LA-4 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDF-46E2000 RM-YD010 US/CND KDF-46E2010 RM-YD010 MEXICO KDF-50E2000 RM-YD010 US/CND KDF-50E2010 RM-YD010 MEXICO KDF-55E2000 RM-YD010 US/CND KDF-55E2010 RM-YD010 MEXICO KDF-50E2010 RM-YD010 LCD PROJECTION TELEVISION 9-883-709-02...
Dolby Laboratories. KDF-46E2000/50E2000/55E2000 KDF-46E2010/50E2010/55E2010 WEGA, Grand WEGA, WEGA GATE, Steady Sound, “BRAVIA” and are trademarks of Sony Corporation. Digital Reality Creation and CineMotion are registered trademarks of Sony Corporation. Design and specifi cations are subject to change without notice. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the POWER/STANDBY will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the POWER/STANDBY fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 9
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 DISPLAY OF POWER/STANDBY OR LAMP LED FLASH COUNT Screen PUSH OPEN TIMER LAMP POWER/STANDBY POWER Indicators - One flash is not us ed for self-diag nosis. Example LED OFF Diagnosis Number of times LED Flash 3.0 sec Lamp cove r...
Page 10
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 VIEWING THE SELF-DIAGNOSTIC ERRORS The TV MICRO service menu contains a Log category that stores the errors. To view the fi rst error detected, display the SHUTDOWN_LOG1 Adjustment Item of the STATUS category. If other errors are detected, they are stored in the SHUTDOWN_LOG2 Adjustment Item of the STATUS category.
Page 12
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SELF-DIAGNOSTIC BLOCK DIAGRAM G BOARD B BOARD CN6800 FAN 1 CN6805 FAN 2 IC3002 TV Micro-computer CN6801 FAN 3 CN6802 CN3002 CN6904 LB-ERROR 10.5V FAN 4 I_FAN_PROT S2 BOARD D_OVP IC160 TEMP I 2 C I 2 C SENSOR...
Page 13
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 READING LAMP AND PANEL TIME RESETTING THE LAMP TIME The TV_Micro menu of the Service Menu displays the current lamp and When replacing the lamp, use the following to reset the lamp time. panel time of a set. The Lamp Hours and Panel Hours are shown in hexadecimal format.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SECTION 1: DISASSEMBLY 1-1. OVERVIEW TOOLS NEEDED Long Phillips Screwdriver Needle Nose Pliers Small Flathead Screwdriver or Jewelers Screwdriver The connectors in the MIX5 chassis have been redesigned to ensure they are securely fasten to the boards. Please review the illustrations below.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-2. REAR COVER REMOVAL Pull down the claw to release the Lamp Door Remove the Lamp Door Remove 13 screws (+BVTP2 4X16) to remove the Rear Cover Lamp door When reassembling the rear cover, be sure to securely lock the lamp door to avoid a lamp cover failure warning.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-3. CHASSIS REMOVAL AND SERVICE POSITION Remove 2 screws to release the Left Stay Disconnect CN8400 from U Board Disconnect CN2500 from K Board Release wires from purse locks Gently pull chassis out towards the right of the TV to access connectors on B Block Assembly.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-5. B BLOCK ASSEMBLY, A BLOCK ASSEMBLY, ANTENNA, U BOARD AND K BOARD REMOVAL Remove 6 screws and 2 hexagon washers to release the Terminal Bracket from the U Board. On the U Board, disconnect CN8400 then using a fl at...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-6. LAMP BLOCK ASSEMBLY AND OPTICAL BLOCK REMOVAL Note: Remove the Lamp door and Lamp before removing the Lamp Block Assembly (See “Replacing the Lamp” in the Appendix section of this service manual.) Remove 2 screws to release the Right Stay.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-6-1. LAMP CONNECTOR AND T2 BOARD REMOVAL Pull retaining clip outward to release and drop the high voltage connector and the T2 Bracket. Separate the HV Connector from the bracket Remove 1 screw to release the T2 Board. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-6-2. LAMP DRIVER FAN REMOVAL From the inside of the assembly, release the 3 claws securing the fan duct, then remove the fan duct by grasping as shown. Remove 1 screw. Release 3 clips to detach cover. Remove Fan.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-7. HC BOARD REMOVAL Remove 2 screws to detach the H2 Bracket. Disconnect connector. Remove 2 screws. Lift out to remove HC Board. 1-8. HA BOARD AND HB BOARD REMOVAL Remove 2 screws from inside the front panel. Using a screwdriver, gently push through the hole to release the speaker grill.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-9. SCREEN FRAME ASSEBMLY AND SPEAKER REMOVAL CAUTION: When removing the Screen Frame Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles. Release the wire harness from the purse locks. Disconnect the CN2500 from the K Board.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 1-10. MIRROR ASSEMBLY AND MIRROR COVER ASSEMBLY REMOVAL CAUTION: When removing the Mirror Cover Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles. Remove 4 screws to release the 2 top mirror brackets.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 WIRE DRESSING BALLAST WIRE DRESSING “Top” Lead Dress Lamp Driver Leads as shown below to wire holders. Dress "Bottom" Lamp Driver Lead as shown to wire holder on Duct Block Assy “Bottom” Lead 1-910-024-31 Connector Assy should be After Installing Duct Block assy to dressed around Heat Sink and around Duct Optical Block Dress “TOP”...
Page 25
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 BALLAST WIRE DRESSING (CONTINUED) 1-910-024-31 Connector Assy should be dressed around Heat Sink and around Duct Block Cover as shown above. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 26
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 BOTTOM BLOCK WIRE DRESSING Before installing chassis Dress CN3004[B], CN8400[U], and CN3008[B] to purse lock on bottom block as shown. Loop Video 2 Connector before installing into Purse Lock as shown to avoid Connector assy from Touching [K] Board Heat Sink.
Page 27
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 C BLOCK WIRE DRESSING Dress 15P CN9000 [C] LVDS Connector and Fan Connector to Purse Lock on [C] Shield Install Conn Assy 1-910-024-21 to "FAN1" Route Optical Block Fan Optical Block Fan. to Wire Holder to avoid being “Pinched” when [G]...
Page 28
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 CHASSIS WIRE DRESSING Dress [B] Block Fan and [K] Board Connector Assy to Purse Lock on [B] Block as shown above. Dress the following DUCT BLOCK ASSEMBLY WIRE DRESSING Connector Assys to Wire Holder on Bottom Block: 1. 1-910-024-29 2.
Page 29
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 G BOARD WIRE DRESSING G-Board Wire Pin Holders Instructions. There are (3) wire pin Holders on the [G] board. See below to see which wires are dressed to each wire pin holder 1. LVDS and 8P CN6009[G] 2. LVDS, 8P CN6009, and 7P CN3004[B] 3.
Page 30
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 OPTICAL BLOCK ASSEMBLY WIRE DRESSING ROUTE IRS CONNECTOR AS SHOWN APPLY HIMELONE TAPE TO SECURE IRIS CON- NECTOR AS SHOWN ABOVE. APPLY TAPE SO THAT THE CONNECTOR ASSEM- BLY WILL NOT BE IN SHADED AREA ABOVE. IF CONNECTOR ASSEMBLY IS IN THE SHADED...
Page 31
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 OPTICAL BLOCK ASSEMBLY LIGHTNING GROUND POSITION 1-910-016-90 x Secure Ring Terminal of 1-910-016-90 to G-Block as shown above. x Install Faston Terminal to Antenna Switch. Note: Orientation of ring terminal should be towards the top of the set. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 32
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER GRILL WIRE DRESSING For 55”, MUST use 2 screws on each side (total 4 screws) to secure Speaker Grill to Screen Frame. For 50” and 46” use only 1 screws each side (total 2 screws) KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 33
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER GRILL WIRE DRESSING (CONTINUED) See above for Connector Assy Routing of CN110 [HB] See above for Connector Assy Routing of CN100 [HA] KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 34
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER GRILL WIRE DRESSING (CONTINUED) When routing HA/HB Connector Assy through Wire Holder Dress HA/HB Connector Assy to Wire holder as shown above. “RED” tape should be approximately in the position shown above. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 35
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER GRILL WIRE DRESSING (CONTINUED) NO Sound Cushion on 55” and 46” Speaker Grill 1) Use Holder (M3), Wire 2- -594-860-01 3x12 screw to wire dress as sh hown 2) Wire must enter from the e bottom of Cable...
Page 36
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER GRILL ASSEMBLY CUSHIONS Add 2-638-237-02 Cushion, Sound (SF) to 55” Speaker Grill 2-671-852- Align Sound (SF) Cushion to the lines as shown KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 37
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER WIRE DRESSING Dress Positive Tab of Speaker wire around speaker bracket and then Himelon Tape should be installed to secure the wire as shown. Tape should wrap around bracket as shown to the right and securely hold the speaker wire so that it does not move once Wire Should be pulled so that there is no excess wire.
Page 38
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SPEAKER WIRE DRESSING (CONTINUED) On “Left” Speaker Secure Speaker wire as shown below using 265206401 TAPE, HIMELON (20X40) Note: PCN MB607734 Shows different Tape position please disregard that location and use above Speaker Bracket must be secured following the above Screw Order.
Page 39
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 RIGHT SPEAKER WIRE DRESSING KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 40
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 LEFT SPEAKER WIRE DRESSING KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 41
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 LEFT SPEAKER WIRE DRESSING (CONTINUED) All these applies for 55”, 46” For 50”, this starts from MP set #1 (no need to re-work PP and PVT sets) KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 CAUTION POINTS BOTTOM BLOCK ASSEMBLY HIMELON TAPE LOCATION Apply tape on B-Shield to keep LVDS Connector Assy and 7P CN3004 Connector on [B] from being "pinched" when Chassis is installed into Bottom Block Himelon Tape should secure the (2) connectors coming...
Page 43
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 BOTTOM BLOCK WIRE DRESSING CAUTION POINTS Before installing chassis Dress CN3004[B], Loop Video 2 Connector before installing CN8400[U], and CN3008[B] to purse lock on into Purse Locak as shown to avoid bottom block as shown. Connector assy from Touching [K] Board Heat Sink.
Page 44
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 CHASSIS WIRE DRESSING CAUTION POINTS 435591211 PURSE LOCK (DIA. 11) -Install Angled Purse Lock to C Shield as shown to the right. -Dress 15P connector Assy, LVDS Connector Assy and Optical Block Fan Connector Assy to Purse Lock as shown.
Page 45
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 DAMPER AND GASKET CAUTION POINTS When Pulling the damper through the fan be careful not to use excessive force which may break the damper in this area 269304701 GASKET(5 X 10 X 30) KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010...
Page 46
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 G BOARD WIRE DRESSING CAUTION POINTS G-Board Wire Pin Holders Instructions. There are (3) wire pin Holders on the [G] board. See below to see which wires are dressed to each wire pin holder 1. LVDS and 8P CN6009[G] 2.
Page 47
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 RIGHT SPEAKER WIRE DRESSING CAUTION POINTS Dress Positive Tab of Speaker wire around speaker bracket and then Himelon Tape should be installed to secure the wire as shown. Wire Should be pulled so that there is no excess wire.
Page 48
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 LEFT SPEAKER WIRE DRESSING CAUTION POINTS Pull wire in direction of arrow to Apply Himelon tape to speaker take out slack wire as shown to the left. Speaker wire must be placed 265206401 TAPE, inside Grooved slot in speaker...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SECTION 2: CIRCUIT ADJUSTMENTS 2-1. USING THE REMOTE COMMANDER 2-3. VIEWING THE SERVICE MENUS FOR ELECTRICAL ADJUSTMENTS Use the Remote Commander to view the 3 service menus options. To adjust various set features, use the Remote Commander to put the 1.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 2-4. USING THE REMOTE COMMANDER TO CHANGE SERVICE DATA TV/VIDEO SLEEP POWER TV POWER BD/DVD DVR/VCR SAT/CABLE Use the buttons on the Remote Commander to access the service menu FUNCTION Increase items and adjust the data values. Display Data Value...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SERVICE MENUS 2-4-1. EXITING SERVICE MODE (CATEGORIES ONLY) After completing the changes, exit service mode by turning off the set using the Remote Commander or the power switch. TV MICRO TV MICRO (cont.) Q BOX VERSION IRIS_DBC NOTE: After exiting service mode wait 2 minutes before restarting IRIS_ADJ the set to allow the fans to shut down properly.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 2-7. H/V CENTER CONFIRMATION AND 2-8. IRIS ADJUSTMENTS ADJUSTMENTS Use the following instructions to adjust the IRIS after replacing either of the following: Use the following instructions to adjust the pictures horizontal and Optical Block Assembly vertical center after replacing either of the following:...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SECTION 3: DIAGRAMS 3-1. CIRCUIT BOARDS LOCATION The C Board is part of the Optics Unit Block Assembly and cannot be ordered separately Power Supply Block 3-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS INFORMATION All capacitors are in µF unless otherwise noted. pF : µµF 50WV or All voltages are in V.
Page 54
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 REFERENCE INFORMATION Terminal name of semiconductors in silk screen printed circuit ( RESISTOR : RN METAL FILM Circuit Device Printed symbol Terminal name Collector : RC SOLID Transistor : FPRD NONFLAMMABLE CARBON Emitter Base : FUSE NONFLAMMABLE FUSIBLE Collector...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 3-3. SIGNAL FLOW BLOCK DIAGRAM FY06 LA4 GW Signal Flow Digital Video Digital Audio Digital Video Analog Video Analog Audio Memory HDMI1 HDMI2 Control HDMI EDID HDMI Rx EDID Micro SiI9023 TMP75 256Mb*2 256k 256Mb*2 (LAMP) NAND YPbPr/RGB Flash...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 3-4. SCHEMATICS AND SUPPORTING INFORMATION A BOARD SCHEMATIC DIAGRAM Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. R1034 —...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (1 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. TIMER_LED_IS_REV ERSED_ON_HB TO HA BOARD...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (2 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. FB3607 L3203 R3234 RB3213...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (3 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. VIDEO APL DETECT C3494 MC2838-T112-1 0 .
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (4 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. — SAIPH_OSD ATI_GRAPHICS —...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (5 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. R3747 Q3603 2SC3052EF-T1-LEF 1/10W...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (6 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. 1005 TU_I2C 6 . 3 V 0 .
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (7 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. D2.6V ASIC CORE POWER D1.2V...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (8 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. — AG25 AG25 DQA31...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (9 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. TERA HAS INTERNAL PULL DOWN —...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (10 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. — 1005 VI_IN0 0 . 1...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 B BOARD SCHEMATIC DIAGRAM (11 OF 11) Due to the complexity of this board, performing component level field repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. ATSC/HDMI/NTSC_AUDIO — LEFT R2003...
Page 69
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 [SAIPH, CCP-XA, HELIOS, DCP/LVDS, HDMI, POWER AND TUNER CONNECTIONS, ATI POWER/GND, DDR/FLASH/NVM, ATI VIDEO/GRAPHICS, FE I/F AND AUDIO SWITCHING, AUDIO] [SAIPH, CCP-XA, HELIOS, DCP/LVDS, HDMI, POWER AND TUNER CONNECTIONS, ATI POWER/GND, DDR/FLASH/NVM, ATI VIDEO/GRAPHICS, FE I/F AND AUDIO SWITCHING, AUDIO]...
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 NOTE: The components identifi ed by shading and mark are critical for safety. NOTE: Les composants identifi es per un trame et une marque sont critiques pour Replace only with part number specifi ed. la securite. Ne les remplacer que par une piece portant le numero specifi e.
DOOR ASSY, LAMP A-1197-240-A OPTICS UNIT BLOCK(IRP)ASSY 2-580-640-01 SCREW, +BVTP2 4X16 F-9308-7500 LAMP BLOCK ASSEMBLY (KDF-46E2000/46E2010 ONLY) 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3 A-1177-123-A T2 BOARD, MOUNTED The C Board is part of the Optics Unit Block Assembly A-1177-122-A T1 BOARD, MOUNTED and cannot be ordered separately.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 SECTION 5: ELECTRICAL PARTS LIST NOTE: The components identifi ed by shading Items marked with an asterisk are not stocked since they RESISTORS mark are critical for safety. Replace only are seldom required for routine service. Expect some delay •...
Page 98
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES FB1007 1-414-226-21 FERRITE 0µH R1022 1-218-911-11 METAL CHIP 470K 0.50% 1/10W FB1008 1-414-226-21 FERRITE 0µH R1023 1-218-891-11 METAL CHIP 0.50% 1/10W FB1009 1-414-226-21 FERRITE 0µH R1024 1-218-867-11 METAL CHIP 6.8K...
Page 122
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 123
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 124
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 125
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 126
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 G HA HB NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Lamp maintains its brightness will vary depending upon your usage and environmental conditions. To maintain the quality of your viewing experience, Sony recommends that you replace the Lamp (1) after approximately 8,000 hours of use (the TV will display a message reminding you to replace the lamp);...
Page 136
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 Remove the outside lamp cover. Remove the lamp door. Turn the knob counterclockwise to OPEN and pull out the cover. Lamp door Pull out the lamp. Hook a finger through the loop of the lamp handle and pull the handle upwards.
Page 137
Put the outside lamp cover back in its place. Select the Lamp Replacement option (MENU > Settings > Setup menu) and follow the on-screen procedure. ✍ Consult your Sony dealer for a Sony XL-2400 replacement lamp. ✍ Take great care when replacing the lamp or plugging in/unplugging the connecting cords.
Page 138
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010 The used lamp For customers in the United States: This product contains mercury. Disposal of this product may be regulated if sold in the United States. For disposal or recycling information, please contact your local authorities or the Electronics Industry Alliance (http://www.eiae.org).
Page 139
In an effort to reduce the size of this pdf file the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.