Related Manuals for Electrolux EURO OVEN
Summary of Contents for Electrolux EURO OVEN
- Page 1 SERVICE MANUAL EURO OVEN WOEC Test program © AEG Hausgeräte GmbH Publ.-Nr.: Muggenhofer Straße 135 599 50 72 16 D-90429 Nürnberg Germany Fax +49 (0)911 323 1420 TSE - N Edition: 12.99...
-
Page 2: Table Of Contents
Page Contents Safety instructions General technical information User technical data Dimensions Hot plate controls Circuit diagram of energy regulator 1 Circuit diagram of energy regulator 2 Oven control Circuit diagram of oven thermostat Thermotronic (electronic oven control, WOEC) WOEC test programmes and their application Descriptions of programme 1 - 6 Fault-finding Service instructions... -
Page 3: Safety Instructions
Safety instructions Attention Please observe the applicable safety requirements according to DIN/VDE 0701 (concerning repairs) and VDE 0700/ICE 355 respectively VDE 0860/IEC 65 (concerning type of product)! Components to IEC or VDE guidelines! Only use components with the same specification for replacement! Controls with MOS components use only components with the same specification. -
Page 4: General Technical Information
General technical information User technical data Capacity Voltage Oven heater (heating element) Heating element bottom 1000 W 230 V Heating element top 1000 W 230 V Heating element grill 1900 W 230 V Heating element circulating air 2400 W 230 V Motor circulating air 35 W 230 V... -
Page 5: Hot Plate Controls
Hot plate controls Circuit diagram of energy regulator 1 Circuit diagram for “OFF” position Circuit diagram of energy regulator 2 Circuit diagram for “OFF” position Circuit diagram of oven thermostat Circuit diagram for “OFF” position TSE-N 12.99 A. B. - 5 - 599 50 72 16 EN... -
Page 6: Woec Test Programmes And Their Application
WOEC test programmes and their application The control is provided with various test programmes, some of which can be switched on manually or run automatically in the background. Safety cut-out The appliance is equipped with a safety circuit which switches it off automatically if the allocated time intervals are exceeded at various temperature settings without the functions or temperature setting being changed. -
Page 7: Descriptions Of Programme
Descriptions of programme 1 - 6 Basic setting - Time flashes or current fault is displayed. - Press quick timer button and button I simultaneously and keep pressed for 5 s. - The programme number appears in the right of the display and can be set to 1-6 using the quick timer button. - Page 8 Programme 2 Relay number Programme number in red white In this programme, the individual relays in the relay unit can be switched on and off by pressing the quick timer button. The relevant relay can be selected by pressing the Cooking time and End of cooking time buttons at the same time.
- Page 9 Programme 3 - see basic setting 1 - 5 Oven sensor Programme number white white Food thermometer white Programme 3 shows the temperature of the oven sensor and the food thermometer (if inserted). Note! The two temperatures normally differ because different measuring points are used.
- Page 10 Fault reports for programme 4 Functional description: When this module is activated, it handles all the faults present and carries out an EEPROM check. As soon as a fault occurs, a fault register has access to the main processor control loop. This causes the control to switch from the current status to the fault mode (except when in the test mode): If a new fault occurs which has a higher priority than the preceding fault, only this higher fault code is displayed.
- Page 11 Programme 5 - see basic setting 1 - 5 This programme starts a display test in which all the symbols and the individual bars of the 7-segment displays are tested. Programme 6 - see basic setting 1 - 5 Temperature Programme number code white...
-
Page 12: Fault-Finding
Fault-finding Fault-finding is simplified by fault code test programmes. Faults which do not constitute a direct danger to the user are not detected by the control, e.g. disconnected heaters. The test programmes still provide help in fault-finding, even if the faults are not detected. -
Page 13: Service Instructions
Service instructions Dismantling front glass oven door and door handle Remove the screws (1), one each on left and right, withdraw the door glass to the front (2) and then downwards (3). When dismantling the oven door handle of an appliance with a plastic door handle, note that this is fixed with two special Torx screws (see diagram). -
Page 14: Rubber Gasket Between Air Duct And Switch Panel
Important! When refitting the switch panel after dismantling it, ensure that the rubber gasket between the air duct and switch panel is properly mounted. TSE-N 12.99 A. B. - 14 - 599 50 72 16 EN...