Digital Imaging Systems Operating Instructions (For Copy & Network Scan Functions) DP-2330/3030 Model No. with Options Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. English...
Getting To Know Your Machine Useful Office Functions Copy Fax/Email • Copy up to Ledger size. • Plain Paper High-speed Super G3 • Capable of copying text/photos/ compatible Fax with JBIG halftone originals. compression when optional Fax Communication Board (DA-FG300) is installed.
Operating Instructions Outline ● Precautions (See pages 7-13) ● Quick Operation Chart (See pages 14 and 15) Getting To Know ● Adding Paper, Replacing the Toner Bottle, Your Machine Removing a Misfed Paper and Error Codes (See pages 14-21) ● Control Panel Key/Button/Indicator Names (See pages 23-25) Before Starting ●...
Getting To Know Your Machine Symbols/Icons The following Symbols/Icons are used throughout this operating instructions manual. Place original(s) on the ADF Getting to know your machine Before starting Place original(s) on the Platen (Book) When making copies Place original on the Platen (Sheet) Press any Hard Key on the control panel or touch any Button...
Getting To Know Your Machine Precautions ■ Laser Safety LASER SAFETY This unit employs a laser. Only qualified service personnel should attempt to service this device due to possible eye injury. CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Precautions For Your Safety To prevent severe injury and loss of life, read this section carefully before using the Panasonic DP-2330/3030 to ensure proper and safe operation of your machine. ■ This section explains the graphic symbols used in this Operating Instructions manual.
Never touch a power cord with wet hands. Danger of electric shock exists. If the power cord is broken or insulated wires are exposed, contact your Service Provider for a replacement. Using a damaged cord can cause fire or electric shocks. Stop operation immediately if your machine produces smoke, excessive heat, unusual noise, or smell, or if water is spilt onto the machine.
Getting To Know Your Machine Precautions CAUTION Do not place a magnet near the safety switch of the machine. A magnet can activate the machine accidentally, resulting in injuries. Do not use a highly flammable spray or solvent near the machine. It can cause fire. When copying a thick document, do not use excessive force to press it against the document glass.
Output Tray more often to avoid paper jams. ■ Use of other than genuine Panasonic supplies can damage the printer. This may void the warranty of the printer and supplies. Be sure to use only genuine Panasonic Toner (DQ-TU15E) designed for the machine.
Page 12
Getting To Know Your Machine Precautions Ventilation ■ The machine should be installed in a well-ventilated area to minimize the ozone density in the air. WARNING For USA FCC WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 13
■ Dept. (Departmental) Code When the Department Counter function is set up, the Dept. (Department) Code input screen is displayed on the LCD Display. A registered Department Code (1 to 8-digit) is required to gain access to each secured function, or the secured Copy/Fax/Scanner function(s) cannot be used.
Getting To Know Your Machine Operation Chart ■ Quick Operation Chart Face Up From COPY If set in other Tray function mode Max. 50 originals* Turn the Main Original Guides *30 originals (Legal/Ledger) Power Switch Adjust to the original’s width on the back of Original Guides the machine to...
COPY Select desired settings SIZE Reduction/ Enlargement only (See page 28) Number of Copies (Max. 999) Adjust the Manual Exposure Select type of Original(s) Text and Photo Mainly Photo Mainly Text combined Select the Exit Destination Receiving Tray (Lower) Receiving Tray (Upper) Tray/1-Bin Finisher (External) •...
Page 16
Getting To Know Your Machine Operation Chart ■ Problem Solving ● Replacing Toner Bottle/Replacing Toner Waste Container Toner Waste Container Replace Toner Bottle Toner Bottle Replace Toner Waste (New) Container Seal Shake the new Toner Bottle well to loosen the contents. ●...
Page 17
Toner Bottle Toner Bottle (Empty) Toner Waste Container Bottle's Green Knob New Toner Bottle New Toner Waste Container (New) Replace the Toner Waste Container Bottle's Green Knob along with the New Toner Bottle. Staple Case Empty Staple Cartridge FQ-SS32 Jammed Staple When the Staple is jammed ●...
Page 18
Getting To Know Your Machine Operation Chart ■ Problem Solving (Continued) ● Removing a Misfed Paper (Paper Entry Area/1st Paper Tray) Misfed Paper Right Cover Right Cover ● Removing a Misfed Paper (Paper Transport Area) Latch Push Misfed Paper When the optional Tray/1-Bin Finisher is installed.
Page 19
Right Paper Clearing Knob Paper Tray Heat Roller Cover Transport Cover Latch ∗ Misfed Paper ∗ Confirm that the latch is securely fastened. Misfed Paper Right Cover Feed Cover...
Page 20
Getting To Know Your Machine Operation Chart ■ Problem Solving (Continued) ● Removing a Misfed Paper (ADF) ADF Cover Misfed Paper Exit Unit ADF Tray ● Removing a Misfed Paper (1-Bin Finisher) Finisher Misfed Paper Release Button Option (DA-FS300)
Page 21
Misfed Paper Exit Unit ADF Tray Misfed Paper NOTE: Finisher If the misfeed indicator(s) do not clear, open the upper cover and remove all misfed paper. When using the Staple Sort, Shift-Sort or Shift-Group mode, remove the remaining copies on the staple tray. Then the copy job will restart.
This product will automatically “power down” after a specified period of non-use. The use of this NERGY ® compliant product will reduce energy consumption and ultimately benefit the environment. The default functions can be adjusted depending on your office requirements. Please ask your authorized Panasonic dealer for more details.
Control Panel ORIGINAL COPY SIZE Touch Panel Keypad START SIZE Keys Keys Display Contents COPY Key ● To use the unit as a photocopier. ENERGY SAVER Key ● Saves power while the copier is not in use. INTERRUPT Key ● Interrupts other copy or print jobs while making copies. FUNCTION Key ●...
Before Starting Touch Panel Display 9 10 Job Status Indicator Ex.: Copying 3 sets. The Indicator displays the progress of a job task as follows: 0/3 → 1/3 → 2/3 → 3/3 ● Use only soft finger pressure to activate the Touch Panel Display. DO NOT USE SHARP NOTE OBJECTS such as pens, fingernails etc., as this may damage the panel.
Page 25
■ Touch Panel Display Indications Contents See Page Warning Indications 14 - 17 : Add Toner : Add Paper : Call Service (Call your Service Provider) : Waste Toner Original Icon — Original Size Indication — Job Build and SADF/Multi-Size Feed Mode Indication 38 and 39 Rotate Mode Indication —...
Making Copies Basic Menu ■ Copying the Same Size Originals (1:1) Copy size is automatically selected. 100% If set in other If original size function mode is not detected ■ Using the ADF Set the originals up to the Originals that cannot be used ●...
Adjust the Manual Exposure Select type of Original(s) Mainly Text Text and Photo Number of Copies combined (Max. 999) Mainly Photo Features Automatic Original Feeding Duplex Copying Insertion/Overlay Feeds originals automatically • Cover Up to 50 Letter size (20 lb) •...
● If the desired copy size is different from the paper size loaded in the Paper Tray, use Sheet NOTE Bypass. (See page 14) The selected Remote printing copier, must be either DP-2310, DP-2330, DP-3010 or DP-3030. For the copier to function as a Remote/Tandem Copier it has to be setup in advance.
Page 29
The Correct ratio is automatically selected. Reduction and enlargement ratios (%) ORIGINAL COPY SIZE SIZE Ledger Legal Letter-R Invoice-R Ledger Legal Letter-R Invoice-R Number of Copies (Max. 999) If the Proof copy is OK, the remaining number of sets will be printed. If the Proof Copy is NG, again, place the originals Number of Copies...
Enter the key name (up to 15 characters). ■ Tandem/Remote Copy Settings (Registration 2) If either DP-2330 or DP-3030 is installed on a Network with a different subnet mask, the DP-2330 or DP-3030 must be regis- tered first, before being able to use the Tandem/Remote Copying function.
Page 31
Scroll to 02/02 Scroll to 07/09 Machine name (up to 15 characters) Button Names on the Keyboard To input upper case letter(s). To move the cursor (_) to the left or right side. To input numbers and/or symbols. To erase the character before the cursor. Scroll to Input ID Code (4-digit)
A Job Completion Notice via a pop up screen on the Desktop of your PC when the Copy Job is com- pleted. Before using the Completion Notice, install the Panasonic-DMS included with the machine. Select Pop up Display Copy is completed.
Page 33
Input password (4-digit) 2 times Number Select the desired of Copies PC Address ● This Completion Notice is available only when connected to the Network. NOTE To reset the Completion Notice, press the CANCEL button.
Making Copies 2-Sided/Original Copy ■ 1-Sided 2-Sided, 2-Sided 1-Sided, 2-Sided 2-Sided Copy 1-Sided 2-Sided Copy 2-Sided 1-Sided Copy Reduction/ Enlargement 2-Sided 2-Sided Copy only 2 Copy only) ● Duplex Notice Function “2-SIDED PRINT” is printed on 1-Sided copy. Bottom Bottom Upper right position center position...
Page 35
Bind position Number of Copies When clearing the 2-Sided Copy: From Platen: When "Last Original?" message is displayed. If required Ex: 2 originals Touch "NO" button. Place next original on the platen. Press Start Key. Touch "YES" button. When DUPLEX NOTICE is selected.
Making Copies 2-Sided/Original Copy ■ 2 Page Copy Copying two facing pages or a Ledger size original on two separate Letter size sheets. Platen Example: Ledger size original Ledger Letter Ledger ■ N in 1 Copy From two/four/six 1-Sided originals, side by side, to 1-Sided pages.
Page 37
When "Last Original?" mes- sage is displayed. Ex: 2 originals Touch "NO" button. Place next original on the platen. Number Copy Format Press Start Key. of Copies Touch "YES" button. ∗ Original Copy direction N in 1 mode layout ex. 2 in 1 Reduction/ Enlargement only...
Making Copies 2-Sided/Original Copy ■ Multi-Size Feeding Use this function when copying mixed Ledger/Letter size originals using the ADF. Original size can be detected automatically then can be copied full size (1:1) or same size. Combination of Multi-Size Feeding Copies Originals Full Size Reduction...
Page 39
Number of Copies Number Place the next original of Copies within 5 sec. of last ejected copy. If “Another Original? YES or NO” message is displayed, touch the “NO” button. Number of Place the next original within Select Sorting/Finishing settings Copies 5 sec.
Making Copies Sort/Finish ■ When using Sort Mode Sort Multiple copy sets are sorted automatically. Rotate-Sort Multiple copy sets are sorted automatically and stacked in alternate direction (rotate). (Letter size only) Rotate-Group Multiple copies of individual pages are stacked in alternate direction (rotate).
Page 41
Number Sort mode of Copies Reduction/ Enlargement only 1-Bin Finisher (DA-FS300) When the optional 1-Bin Finisher is installed, this screen will change as follows: For DA-FS300 ● Electronic Shift-Sort ● When copying with Legal/Ledger size, pull out the bin until it stops. ●...
Making Copies Zoom/Effects ■ Zoom Copies with variable zoom ratios from 25 % to 400 % in 1 % increments. 400% ■ Auto Zoom The copy Zoom Ratio adjusts automatically to the selected paper size. Opening the ADF Fit to paper length or width Fit to paper length and width ■...
Page 43
Same vertical and horizon- Different vertical and tal ratio horizontal ratio Number 25% - 400% 25% - 400% of Copies or Keypad or Keypad Paper Size Number (Paper Tray) Fit to paper length or of Copies width Fit to paper length and width Same vertical and horizon- Different vertical and...
Making Copies Zoom/Effects ■ Margin Shifts image to right, left, up or down. ■ Centering Copy image can be centered automatically on selected paper. Opening the ADF ■ Image Repeat Creates continuous copy image on one sheet. Minimum original size: 20 x 20 mm Opening the ADF The dotted line can be set to “None”...
Page 45
If a part of the copied image is missing when using the Margin mode, change the Margin Reduction setting to Yes. (See page 58) Number of Copies 5 - 99 mm Margin area or Keypad Paper Size Number (Paper Tray) of Copies Paper Size Number...
Making Copies Zoom/Effects ■ Stamping (Page Numbering) Page numbers can be automatically stamped on each page. ADF only ∗ The page numbering format can be changed in function mode. Default format is "-n-". (See page 59) ■ Stamping (Date Stamp) The date can be automatically stamped on each page.
Page 47
ORIENTATION Number of Copies Stamping start page (Max. 999) From 1, 2 or 3 Stamping position From 3rd page From 2nd page ● Multiple copy sets will be From 1st page sorted automatically. ORIENTATION Number of Copies (Max. 999) Changing the stamp date Stamping position ●...
● Certain types of transparency film may not be compatible and may damage your machine. NOTE Consult with an authorized Panasonic dealer for advice regarding non-standard paper types. (Panasonic has tested "3M PP2500" transparency film and found it to be compatible.)
Page 49
Cover Page mode Number of Copies Cover (Front) Cover (Front+Back) Paper Size ∗ (Max. 999) Paper Tray Blank Copy Number of Copies Page Insertion mode Paper Size ∗ Set the insert page position with (Max. 999) Keypad ∗∗ Paper Tray Blank If selecting other position, move the sheet with...
Making Copies Insertion/Overlay ■ Overlay Overlays a second image onto the first by using a second original. 1st-page ■ File Edit Up to three ∗ editing functions available in the Form Overlay feature. ∗ : To Add a new file ∗ ∗∗...
Page 51
Select the overlay image to store Number of Copies From Platen: Density for 1st page image into memory for later use. (Max. 999) Same procedures as for Form Overlay REGISTER Density for File Name registered To cancel the registration, image touch "CANCEL"...
Making Copies Other Features ■ Job Memory Five Copy Jobs can be stored in Memory To store a job in memory (M1 to M5) for recall at a later time. Set up the copy job to be stored. NOTE: When the M5 Key is used, the Double Exposure Mode should be set to "Off"...
Page 53
To recall a job stored in memory Number of Copies (Max. 999) M1, M2, M3, M4, M5 NOTE If “2: NO” is selected, the machine will start copying only scanned original. Number of Copies (Max. 999) The following steps, illustrate how to make multiple copies when the Sort Mode is selected.
Making Copies Other Features ■ Skyshot Mode Skyshot allows copying a manuscript without generating dark borders even if the platen cover or ADF is opened. Two types of Skyshot modes can be selected; Digital Skyshot Mode : The scanning area (size) is not pre-determined. Manual Skyshot Mode: The scanning area (size) is pre-registered into memory (M1 and M2) in advance.
Manual Skyshot Mode ● Set “09 Manual Skyshot Mode” in Copier Settings first. (See page 58) Platen Upper- Left Corner Number of Copies Custom size ∗ (Max. 999) ∗ Default M1/M2 size can be changed by Function mode. (See page 64) Select Function Job Waiting List can be...
Function ■ Using Function Modes to Change the Initial Modes Options General Copier Printer Fax/Email Scanner Settings Settings Settings Settings Settings Input Identification (Key Operator ID) Code General Copier Printer Fax/Email Settings for Settings for Settings for Settings for Key Operator Key Operator Key Operator Key Operator...
Page 57
Copier Settings: Changing the Initial Copy Modes ● Default function of each copy mode (See pages 58 and 59) For Key Operator: Paper size priority, Original mode, Contrast, Job Build and SADF mode, Original size of Manual Skyshot mode, etc. (See page 64) Printer Settings: Changing the Initial Printer Modes...
Function ■ General Settings Screen Initial Modes Function Setting 00 Power On Default Mode Selects mode. Copy ● COPY, FAX, PRINTER, SCANNER 01 Manual Copy Quality Adj Sets to activate the manual density control. ● Off, On 02 Manual Add Toner Adds toner manually.
To delete address. ∗ 08 Delete Address 09 XMT File Type Sets the default XMF File Type. ● TIFF, PDF ∗ Address Book is not necessary to set in this function setting, your PC can be registered with NOTE Panasonic-DMS. (See page 72)
Function ■ Printer Settings Screen Initial Modes Function Setting 00 Number of Prints Sets the initial number of prints. ● 1 ~ 999 01 Paper Size Sets the paper size setting. LETTER ● A3, B4, A4, B5, A5, LEDGER, LEGAL, LETTER, INVOICE, 8 x 13, 8.5 x 13 01/04 02 Paper Tray...
For Key Operator ■ General Settings Screen Initial Modes Function Setting 00 Print General Settings Prints the initial user settings of the common menu. Start ● Stop, Start 01 Paper Size Sets the paper size of each Paper Tray. Consult with an ●...
Page 62
Function For Key Operator ■ General Settings Screen Initial Modes Function Setting 20 Date Time Setting Sets the registered date and time. ● Month, Day, Year, Time 21 Weekly Timer Sets the weekly On/Off timer. ● Off, On (See page 66) 22 Daylight Time Sets the daylight time.
Page 63
● Enables read Input the device name when required. ∗∗ 35 Device Name Panasonic (For Status Monitor/EtherTalk Machine Name) DP-2330 or DP-3030 Input the device location when required. ∗∗ 36 Device Location (For Status Monitor) 37 Routing Menu Function Selects the Document Distribution function.
Function For Example ■ Changing the Auto Contrast Setting You can select whether to automatically adjust the copying density for Text and Photo originals. Scroll to 03/04 ■ Changing the Paper Size The Paper Trays are designed to accommodate Invoice, Letter, Letter-R, Legal and Ledger Size paper. Scroll to 02/02 Paper Tray...
Page 67
ID Code (4-digit) Pull out the Paper Tray Adjust the Paper Guides ( a / b ) Change the Paper Size Indicator Note: It is recommended that the paper guide ( b ) is fixed in place with screws. Consult an authorized service provider for details on how to fasten the guide. ID Code Scroll to (4-digit)
Function For Example ■ Department Counter The Department Counter feature can limit the number of copies, administer counters and Identification Code numbers for each department. (Maximum Number of Departments: 300) Contact your authorized service provider to enable the Department Counter feature. Scroll to 02/02 For Total Counter...
Page 69
Scroll to ID Code 04/09 (4-digit) For Department Counter For Maximum Prints Clear the Maximum number counter (8-digit) of Copies (8-digit) Select Page Select Page to “0” Select Department Select Department ID Code (4-digit) Turn the Power Switch on the Left Side of the machine OFF and ON.
Function Combined Function Table SORT/ INSERTION/ 2-SIDED/ORIG. ZOOM/ Others FINISH COPY EFFECTS OVERLAY Next Selections First Selections Book 2 Page N in 1 Booklet Multi-Size Feeding Job Build and SADF Sort Shift-Sort Rotate-Sort Staple-Sort Shift-Group Rotate-Group Non-Sort Zoom Auto Zoom Edge Book Margin...
Accessories Components ■ The DP-2330/3030 is a digital photocopier which can produce images with great clarity. Furthermore, its copying functionality can also be greatly enhanced by the addition of the following options and supplies. We hope you find that the wide ranging capabilities will make your office-place more productive and efficient.
■ Registering your PC When the Panasonic Document Management System (PDMS) is installed on the provided CD-ROM, starts the Panasonic communication utility and, it is possible to register the your PC of use to the knitting machine by setting network scanner.
Page 73
Click OK. When the DP-2330/3030 is installed different subnet mask ∗ ∗ ∗ ∗ ∗ of the network. Input the machine's Device Name and IP Address. Click OK. Returns to the screen on the left.
Problem Solving Troubleshooting Check Action Unit Does Not Operate Check if the Power Switches (Main Power Switch on the back and Power Switch on the Does the display light? Left Side of the machine) are turned ON and if the power cord is plugged into the AC outlet. Does the Energy Saver key flash (or light) and displays are turned OFF? Press Energy Saver key on the control panel.
Check Action Marked Copies Is the copier Platen Glass or Platen Sheet Clean the Platen Glass or Sheet. dirty? Cover the original with a sheet of white paper Is the original an OHP film or a dark original? before copying or lighten the exposure setting. ■...
Problem Solving Replacing the Battery/Set the Date and Time The copier has an internal battery (Product No.: Remove CR2032) which maintains the date and time. 1 Screw In the event the battery requires replacement, the following message will be displayed. Battery Holder Turn the Power Switch on the Right Side of Control Panel...
Page 77
Install Used 1 Screw Turn the Power Switch on the Left Side of the machine to the ON position. Battery Holder Right Side of Control Panel ID Code (4-digit) Time Month, Day, Year, Time Month/Day/Year/Time CAUTION denotes hazards that could result in minor injury or damage to the machine. ●...
Others INDEX 1-Bin Finisher Components ····························································· 71 Function ··································································· 61 Edge ············································································ 42 Functions Indication ················································· 24 Energy Saver ······························································ 54 Making Copies ························································· 40 ENERGY SAVER Key ··········································· 23, 54 Replacing Staple Cartridge ····································· 16 Energy Star ································································· 22 Removing a Misfed Paper ········································...
Page 84
PANASONIC MACHINE, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PANASONIC DIGITAL DOCUMENT COMPANY ASSUMES NO RISK AND SHALL NOT BE SUBJECT TO LIABILITY FOR ANY DAMAGE, INCLUDING, BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS SUSTAINED BY THE CUSTOMER IN CONNECTION WITH THE USE OR APPLICATION OF THIS PANASONIC MACHINE.