Mikado Logo 500 Manual

Mikado Logo 500 Manual

Mikado logo 500 model helicopter manual

Advertisement

Manual
www.mikado-heli.de
LOGO 500
Mikado Modellhubschrauber • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany
phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de
© Mikado Model Helicopters GmbH, V1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Logo 500 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mikado Logo 500

  • Page 1 Manual www.mikado-heli.de LOGO 500 Mikado Modellhubschrauber • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de © Mikado Model Helicopters GmbH, V1.1...
  • Page 2: Table Of Contents

    Investigate the reason and fix fly alone! the problem. Do not operate the model again as long as the problem is not solved, as this may lead to further Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 2...
  • Page 3: Mainframe

    6). M2,5x10 M2,5x8 10x19x5 M3x10 M2,5x16 M2,5x12 M3x20 M3x45 3x5x1,2 M2,5x8 M2,5x12  M3x20 M2,5x12 M2,5x16 (4x) M3x20 All parts shown in the boxes are displayed in real size. Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 3...
  • Page 4: Tail Rotor & Tail Boom

    M2x6 M3x3 Apply grease M2 Stop 2,5x6x0,5 to bearing M2,5x30 M2,5x6 Kugel/ball/Rotule Ø6x3 M3x30 Bag 6 + 11 M3x30 Bag 6 + 11 5 Min. Epoxy 5 Min. Epoxy Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 4...
  • Page 5: Main Gear & Tail Boom Assembly

    Secure scids using set screws 3x3. Tighten the pivot bolts very carefully. Do not (7x) overtighten them, as Tighten tooth belt: they will break off. Pull tail boom backwards and tighten screws Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 5...
  • Page 6: Bar Rotor Head

    Elevator Rudder Apply a small amount of oil to the rotor shaft. Attach the ball links so that the engraved number is on the outer surface pointing towards you. Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 6...
  • Page 7: Servo Installation

    Please adjust the swashplate driver in such a way that the balls on the inner and outer ring of the swashplate are positioned exactly on a line along the longitudinal axis of the heli. Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 7...
  • Page 8: Mounting The Motor

    0.7 diameter 6 mm Shorten cap (not included in kit) Bag 1 15 teeth #4315 16 teeth #4316 17 teeth #4317 3x5x1 18 teeth #4318 M3x6 *for max. to 6S LiPo Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 8...
  • Page 9: Radio And Battery

     Position of servo arms for the aileron servos Receiver V-Bar Main board when sticks are centered (0 deg. Pitch) Battery: Attach the battery with Velcro. speed controller Velcro Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 9...
  • Page 10: Overview Chassis

    9 Overview Chassis LOGO 500 #04433 Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 10...
  • Page 11: Overview Tail Rotor

    1455 4189 2470 4104 4189 1440 2465 2449 2476 2466 2461 2470 2074 1941 1956 2490 1920 3051 2462 2491 2397 4137 2074 4071 3049 4095 722 (SET) 4070 Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 11...
  • Page 12: Overview V-Bar Head

    11 Overview V-Bar Head www.mikado-heli.de Construction & Rendering: Mehran Mahinpour Tirooni • Layout & Realisation: CDT-Berlin Manual LOGO 500 - ©Mikado Model Helicopter GmbH - Page 12...

Table of Contents