Mikado LOGO 500 SE Manual

Mikado LOGO 500 SE Manual

Hide thumbs Also See for LOGO 500 SE:

Advertisement

Quick Links

Manual
www.mikado-heli.de
LOGO 500 SE
Mikado Modellhubschrauber • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany
phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de
© Mikado Modellhubschrauber, V1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOGO 500 SE and is the answer not in the manual?

Questions and answers

Summary of Contents for Mikado LOGO 500 SE

  • Page 1 Manual www.mikado-heli.de LOGO 500 SE Mikado Modellhubschrauber • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de © Mikado Modellhubschrauber, V1.1...
  • Page 2: Table Of Contents

    Turn off all power switches and always be assisted by an experienced pilot and never Receiver disconnect the batteries. Investigate the reason and fix fly alone! Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 2...
  • Page 3: Mainframe

    6). M2,5 10x19x5 Bag 10 3x7x3 10x19x5  M2,5x8 Bag 12 M2,5x10 M3x10 M2,5x16  M2,5x12 M2,5x16 (4x) All parts shown in the boxes are displayed in real size. Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 3...
  • Page 4: Tail Rotor & Tail Boom

    5 Min. Epoxy Attach the ball links so that the engraved 5x13x4 number is on the outer surface pointing to- M2,5x30 (2x) M2,5x30 (6x) wards you. 3x6x2,5 Ball Ø6 mm Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 4...
  • Page 5: Main Gear & Tail Boom Assembly

    M2.5x8 socket head cap screw here. Use a Pull tail boom backwards and tighten screws 2 mm drill to make a hole in the boom. Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 5...
  • Page 6: Radio

    Futaba with Virtual Flybar for Futaba G3 receiver check the V-bar manual Aileron Rudder Air Speed Sensor Elevator Aileron right V-Bar Mainboard Bluetooth Modul Aileron left Throttle Elevator 3-axis Gyro Rudder Throttle Pitch Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 6...
  • Page 7: Servo Installation

    Elevator Aileron left Aileron right Rudder M2x14 Use M2x14  Attach the ball links so that the engraved number is on the outer surface pointing towards you. Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 7...
  • Page 8: Mounting The Motor

    #4219 available pinions for module 0.7 diameter 6 mm (not included in kit) 15 teeth #4315 16 teeth #4316 17 teeth #4317 18 teeth #4318 *for max. to 6S LiPo Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 8...
  • Page 9: Radio And Battery

    (0 deg. Pitch)  Battery: Attach the battery with O-rings speed and Velcro. controller Rings (2x) Position of LiPo battery Velcro for the power supply of receiver. Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 9...
  • Page 10: Overview Chassis

    4094 (M07 153 Z) LOGO 500 SE #04247 2074 4058 4067 LOGO 500 #04159 1954 1344 1954 LOGO 500 #04248 2495 2775 (500 DX/3D) 2496 (600 DX/3D) LOGO 500 #04155 Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 10...
  • Page 11: Overview Tail Rotor

    1962 (5x) 3078 4104 1941 2466 3086 3051 4275 2467 2476 3077 2449 2449 3051 4069 2074 2462 1956 2397 4174 2074 1941 3049 2491 2461 4137 2481 4237 4276 (SET) Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 11...
  • Page 12: Overview V-Bar Head

    #4148 (6 mm) should be installed. Install bolt only if motorshaft does not reach the ball bearing. cut to 14 mm length M3x35 www.mikado-heli.de Construction & Rendering: Mehran Mahinpour Tirooni • Layout & Realisation: CDT-Berlin Manual LOGO 500 SE - ©Mikado Modellhubschrauber - Page 12...

Table of Contents