NAD C 355BEE Owner's Manual page 10

IDENTIFICATION OF CONTROLS
SR 6 REMOTE CONTROL
The SR 6 remote control handset handles the key functions of the
C 355BEE as well as other NAD Stereo Receivers, Integrated Amplifiers
and Preamplifiers. It has additional controls to remotely operate NAD CD
Players, FM/AM Tuners and dedicated FM/AM/DAB Tuners. It will operate
up to a distance of 16ft (5m). Alkaline batteries are recommended for
maximum operating life. Two AAA (R 03) batteries should be fitted in the
battery compartment at the rear of the Remote Control handset. When
replacing batteries, check that they have been put in the right way round,
as indicated on the base of the battery compartment.
When a command from the remote control is received, the Standby/
protection indicator will blink. Note that the indicator may also blink
when receiving commands not necessarily for the C 355BEE but for other
components in the system. Please refer to previous sections of the manual
for a full description of individual functions.
1 POWER ON & OFF: The SR 6 remote has a separate ON and OFF
button. This can be particularly useful to keep components within a
system "in sync": This way all components will switch to standby when
OFF is pressed or switched to operating mode when ON is pressed
- instead of some components switching ON when the C 355BEE is
switched to Standby. (Note that the other components have to be
capable of responding to the separate ON and OFF commands as well).
Press the ON button to switch the unit from Standby to operating
mode; The Power/Standby/Protection LED indicator will turn from
amber, to red, then to green and the indicator for the last selected
input will blink and light up. Press the OFF button to switch the unit to
Standby mode: The Power/Standby/Protection LED indicator will light
up amber.
2 INPUTS: The input selector buttons perform the same functions as the
buttons labeled the same on the front panel.
3 NUMERIC KEYS: The numeric keys allow for direct input of tracks for
CD players, and direct channel/preset access for tuners and receivers.
4 DIMMER: Press this button to dim the front panel display. Depending
on the NAD model, the brightness of the front panel display will vary
when you toggle this button.
5 CD PLAYER CONTROL (for use with NAD CD Player)
engages Pause
engages Stop
engages Play
/ engages reverse or forward Scan
/ engages reverse of forward Skip
engages CD drawer Open/Close; Press once to open the CD drawer
then once again to close the CD drawer
RPT. This button engages the Repeat Play mode for disc playback.
Toggle to repeat one track, repeat all tracks or turn off repeat play
mode.
6 TUNER CONTROL (for use with NAD AM/FM/DAB Tuner)
TUNE : or scans respectively higher or lower station frequencies for
both AM and FM.
PRESET or : Selects respectively higher or lower number station
preset.
DISP/INFO: Repeatedly pressing this button will show information as
supplied by the current radio station. The applicable display contents
include related DAB display information and RDS broadcast data.
ENTER: With a dedicated FM/AM/DAB tuner, toggle this button to
select manual tune, preset tune or auto tune.
10
AUTO TUNE: In DAB mode, press this button to automatically scan all
available local stations.
FM MUTE: In DAB mode, pressing this button will activate Dynamic
Range Control, preset tune, manual tune, station order or other
appropriate features. In FM mode, press this button to select the stereo
or mono mode for FM tuning.
BLEND: The Blend button toggles between engaging and disengaging
the Blend feature. The NAD Blend feature will allow you to reduce the
amount of noise and hiss normally associated with received weak radio
stations but still retain some level of stereo separation, instead of mono.
AM/FM/DAB: In tuner mode, toggle this button to switch to DAB, FM
and AM frequency bands.
7 SLEEP: Press SLEEP to switch off the applicable tuner after a preset
number of minutes. Each consecutive press will reduce the sleep time
in preset increments until sleep mode is cancelled as could be shown in
the front panel display.
8 TUNER/CD: The TUNER/CD switch applies relevant tuner controls
when in the TUNER position, and applies CD controls to the appropriate
buttons when in the CD position.
9 VOLUME: Press VOLUME or buttons to respectively increase or
decrease the loudness level. Release the button when the desired
level is reached. The motorised Volume control on the front panel will
indicate the level set. The Volume buttons do not affect recordings
made using the Tape outputs but will affect the signal going to the Pre-
amp outputs.
10 MUTE: Press the MUTE Button to temporarily switch OFF the sound to
the speakers and headphones. MUTE mode is indicated by the Power/
Standby/Protection LED indicator on the front panel flashing. Press
MUTE again to restore sound. Mute does not affect recordings made
using the Tape outputs but will affect the signal going to the Preamp
outputs.
11 SPK A, SPK B: The SPK A and SPK B buttons engage or disengage the
speakers connected respectively to the C 355BEE's Speakers A and
Speakers B terminals. Toggle SPK A to switch ON or OFF the speakers
connected to the speaker A terminals. Toggle SPK B to switch ON or OFF
the speakers connected to the speaker B terminals. Press both buttons
to engage both speakers.
12 DEV 1/DEV 2: The default setting for this SR 6 remote control is set to
DEV 1. In this position, the Tuner/CD switch allows for both CD control
and AM/FM Tuner functions. If one switches to DEV 2, the applicable
buttons will remain for CD control buttons and now for dedicated
AM/FM/DAB Tuner functions.