1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. C356BEE
  6. Owner's manual

NAD C 356BEE Owner's Manual

Stereo integrated amplifier
Hide thumbs Also See for C 356BEE:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Owner's Manual
C 356BEE
®
Stereo Integrated Amplifier
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD C 356BEE

Summary of Contents for NAD C 356BEE

  • Page 1 C 356BEE ® Stereo Integrated Amplifier Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE. 14 Outdoor Antenna Grounding - If an outside antenna or cable system FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE is connected to the product, be sure the antenna or cable system is AUDIO EQUIPMENT.
  • Page 3 Changes or modifications to this equipment not expressly approved by 23 Heat - The product should be situated away from heat sources such as NAD Electronics for compliance could void the user’s authority to operate radiators, heat registers, stoves or other products (including amplifiers) this equipment.

  • Page 4: Notes On Environmental Protection

    ONLY TO THE PRESCRIBED AC OUTLET, I.E., 120V 60HZ OR 230V 50HZ. RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT) The model and serial number of your new C 356BEE are located on the back of the cabinet. For your future convenience, we suggest that you record these numbers here: Model no: .

  • Page 5: Getting Started

    Switch off the POWER switch if you intend not to use the C 356BEE for long periods of time (such as when on vacation). Should water get into your C 356BEE, shut off the power to the unit and disconnect the plug from the mains power source. Have the unit inspected by a qualified service technician before attempting to use it again.

  • Page 6: Identification Of Controls

    C 356BEE to a strong light source such as direct sunlight or illumination. loudspeaker impedance and short circuit, the C 356BEE will engage its If you do so, you may not be able to operate the C 356BEE with the Protection circuitry, indicated by the Standby LED turning from blue to remote control.
  • Page 7 Tone Control circuits are bypassed. The Tone Control circuits are active when the TONE DEFEAT LED indicator stays extinguished. 10 TONE CONTROLS: The C 356BEE is fitted with BASS and TREBLE tone controls to adjust the tonal balance of your system. The 12 o’clock position is “flat”...

  • Page 8: Rear Panel

    ATTENTION! Please make sure that the C 356BEE is powered off or unplugged from the mains power source before making any connections. It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections.

  • Page 9: To Make A Recording

    MAIN IN sockets. C 356BEE or back to standby mode. Switch off the POWER switch if you intend not to use the C 356BEE for long periods of time (such as when Always turn the C 356BEE and associated external preamplifiers OFF on vacation).
  • Page 10 Consult with your NAD dealer on how to procure the PP 375 and optional Modular Design Construction (MDC) module. An example its consequent installation to the C 356BEE. Check out also the NAD of a C 356BEE-compatible MDC Classic module is the PP 375 Phono website for any announcement about future release(s) of other Preamplifier module.
  • Page 11 SR 8 REMOTE CONTROL USING THE SR 8 REMOTE CONTROL The SR 8 remote control handset handles the key functions of the C 356BEE as well as other NAD Stereo Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DB Tuners.
  • Page 12 IDENTIFICATION OF CONTROLS SR 8 REMOTE CONTROL CD PLAYER CONTROL (for use with compatible NAD CD Player): Set the DEVICE SELECTOR to “CD” in order to gain access to these buttons. Some of the control buttons below are applicable only to specific NAD CD Player models; check the owner’s manual of your NAD CD Player for control button compatibility.
  • Page 13 IDENTIFICATION OF CONTROLS SR 8 REMOTE CONTROL USING THE SR 8 REMOTE CONTROL LIBRARY The SR 8 can store a different library of default NAD codes for each of its DEVICE SELECTOR “pages. ” If the original default library does not control your NAD CD player, DVD player, or other component, follow the procedure below to change the library code.

  • Page 14: Troubleshooting

    • Check or replace battery. Follow correct control commands. battery insertion setup. • Infrared receiver (IR) window of the C 356BEE • Check IR windows and ensure clear line-of- or IR transmitter of the remote control is sight from remote control to C 356BEE.

  • Page 15: Specifications

    REFERENCE SPECIFICATIONS PREAMPLIFIER SECTION LINE LEVEL INPUT, PRE OUT 20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100 <0.005 % at 2 V out Signal-to-Noise Ratio >106 dB (IHF; A-weighted, ref. 500 mV out, unity gain) >114 dB (A-weighted, ref. 2 V out, Volume maximum) >92 dB (ref.

  • Page 16: Overall Specifications

    5 Measured with MM cartridge connected (600 mH + 600 ohms). 6 Gross dimensions include feet, volume knob and tightened speaker terminals. Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest information about C 356BEE.
  • Page 18 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents