Water Supply Requirements; Electrical Requirements - Jenn-Air DRAWER DISHWASHER Installation Instructions Manual

Preferred Utililty Area
A
¹⁄₂"
(1.3 cm)
25"
(63.5 cm)
B
A. Left-hand or right-hand drain and water connection route
B. Left-hand or right-hand electric connection route
NOTES:
■
All holes should be drilled at 1½" (3.8 cm) diameter.
■ If the cabinet is wood, sand the hole until smooth. If the
cabinet is metal, cover the hole with a grommet (Part
Number 302797).
■ For power supply cord connection, a mating, grounded
3 prong outlet is required in a cabinet next to the dishwasher
opening.

Water Supply Requirements

■ A hot water line with 20-120 psi (138-862 kPa) water pressure.
■ 120°F (49°C) water temperature at dishwasher.
■
Flexible stainless steel braided fill line (½" minimum plastic
tubing is not recommended).

Electrical Requirements

WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
8"
(20.3 cm)
GROUNDING INSTRUCTIONS
■
For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dishwasher is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and
ordinances.
WARNING:
Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
dishwasher is properly grounded. Do not modify the
plug provided with the dishwasher; if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
■
For a permanently connected dishwasher:
The dishwasher must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the dishwasher.
SAVE THESE INSTRUCTIONS
It is the customer's responsibility to:
■
Contact a qualified electrician.
■
Ensure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
Requirements:
■ 120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical
supply
■ Copper wire only, 2 wire with ground
Recommended:
■ Time-delay fuse or circuit breaker
■ Separate circuit
Direct Wire Connection
■
Use flexible, armored or nonmetalic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
■ Use strain relief method provided with house wiring junction
box or install a UL-listed/CSA-approved clamp connector to
the house wiring junction box. If using conduit, use a
UL-listed/CSA-approved conduit connector.
Power Supply Cord Connection
Use Power Supply Cord Kit (Part Number 4317824) marked for
use with dishwashers. Kit contents include:
■
Voltex, Inc., UL-listed 16-gauge 3-wire power supply cord with
3 prong grounding plug
Neer C-500 ⁷⁄₈" strain relief
■
■ 3 wire connectors
■ Grommet (Part Number 302797)
Follow the kit instructions for installing the power supply cord.
NOTE: Power supply cord must plug into a mating, grounded
3 prong, outlet, located in the cabinet next to the dishwasher
opening. Outlet must meet all local codes and ordinances.
5