Primo Water 900137 Instruction Manual

IMPORTANT: Do Not Return Dispenser to Store. If you have questions or issues please contact 1-866-429-7566 for expert assistance.
Spill Proof
Water Dispenser
Model # 900137
TO REDUCE THE RISK OF INJURY
AND PROPERTY DAMAGE, USER
MUST READ THIS MANUAL
BEFORE ASSEMBLING, INSTALLING
& OPERATING DISPENSER.
SAVE THIS MANUAL
FOR FUTURE USE
LOCATING DISPENSER
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded
location near a grounded wall outlet.
Notice: Do NOT plug in power cord yet.
3. Position dispenser so the back is at least 4 inches from wall and
there are at least 4 inches of clearance on both sides.
4. Install Wall Mount Strap to prevent
accidental tip over:
- Unclip strap from back of
dispenser
- Mount strap 25" up from floor
directly to wall stud with screw
(Illustration A)
If stud is not available, insert
and turn anchor directly into
sheet rock using a Philips
screwdriver (DO NOT drill hole
into sheet rock first when using
this anchor). Secure strap by
installing screw through
washer, then eyelet in strap and
into wall mounted anchor.
(Illustration B)
- Position cooler in place
- Clip strap onto back of cooler to
right or left side. (Illustration C)
- Adjust length of strap so the
dispenser can NOT move
forward.
FEATURES & FUNCTIONS
Water Bottle – Not included. Uses 3, 4 or 5 gallon bottles. Go to
www.PrimoWater.com to find Primo Water at a store near you.
Spill Proof Bottle Receptacle with Leak Guard – For fast, easy, spill-
proof loading. Reduces leaks from worn & damaged bottles.
Cold Water Control – Depress control to dispense. Release to stop.
Hot Water Control with Child Safety Feature – Slide red button away
from you and depress control to dispense. Release to stop.
Indicator Lights – Green cold icon (snowflake) means the dispenser is
cooling water. Green hot icon (wavy lines) means the dispenser is
heating water. No green icons means hot and cold water is ready.
LED Nightlight – Helps in low light situations.
Bottle Support – Helps align sports bottles and glasses with spout to
eliminate spills.
Spout – Hot and cold water comes out here.
Drip Tray & Grid – Dishwasher safe. Snaps in and out. Position glass,
cup or pot over center hole in grid to avoid spills.
Energy Saver Switches – Located on back. Switch red control to off to
stop heating. Switch green control to off to stop cooling.
Nightlight Switch – Located on back. Switch to off to turn light out.
GETTING STARTED
Assemble
3. Remove drip tray and grid assembly from protective packaging.
4. Snap drip tray and grid assembly in place.
Install Water Bottle
4. Remove tamper seal from top of bottle cap. Do NOT remove plastic cap.
5. Clean bottle cap and neck with a cloth and warm soapy water, then rinse.
6. Lift bottle and insert onto the probe. Apply slight pressure until the plug
inside the cap pushes in and the bottle is seated. Water will begin to flow
into the reservoirs causing air bubbles in the bottle.
Provide Electricity
Plug cord into a properly grounded wall outlet.
Activate Heating & Cooling
Turn power switches on back of dispenser to ON to start heating and cooling
water.
- If you do not want to heat water, turn the red switch to OFF.
- If you do not want to cool water, turn the green switch to OFF.
Activate Nightlight
Turn nightlight switch on back of dispenser to ON.
Register Online
While you wait for your dispenser to get the water hot and cold, please register
your dispenser. This will be helpful should you need customer service
assistance in the future.
Go to www.PrimoWater.com. and click on Customer Care.
Please visit www.PrimoWater.com for more useful information, instructional videos, tips and special offers.
SAFETY PRECAUTIONS
To reduce risk of injury and property damage, user must read this
entire guide before assembling, installing & operating dispenser.
Failure to execute the instructions in this manual can cause
personal injury or property damage.
This product dispenses water at very high temperatures. Failure to
use properly can cause personal injury.
When operating this dispenser, always exercise basic safety
precautions, including the following:
 Prior to use, this dispenser must be properly assembled and installed in
accordance with this manual.

This dispenser is intended for water dispensing only. Do NOT use other liquids.
Do NOT use for other purposes. Never use any other liquid in the dispenser
other than known and microbiologically safe bottled water.

For indoor use only. Keep water dispenser in a dry place away from direct
sunlight. Do NOT use outdoors.
 Install and use only on a hard, flat and level surface.
 Do NOT place dispenser into an enclosed space or cabinet.

Do NOT operate dispenser in the presence of explosive fumes.
 Position back of dispenser no closer than 4 inches from wall and permit free
airflow between wall and dispenser. There must be at least 4 inches clearance
on the sides of the dispenser to permit airflow.
 Use only properly grounded outlets.
 Do not use an extension cord with your water dispenser.

Always grasp plug and pull straight out from outlet. Never unplug by pulling on
power cord.
 Do NOT use dispenser if cord becomes frayed or otherwise damaged.

To protect against electric shock, do NOT immerse cord, plug, or any other part
of dispenser in water or other liquids.
 Ensure dispenser is unplugged prior to cleaning.

Never allow children to dispense hot water without proper and direct
supervision. Unplug unit to prevent unsupervised use by children.
 Service should be performed only by a certified technician. Please contact us at
866-429-7566 for assistance.
DISPENSING WATER
This unit has been tested and sanitized prior to packing and shipping. During
transit dust and odors can accumulate in the tank and lines. Dispense and
dispose at least one quart of water prior to drinking any water.
Dispensing Cold Water
After setup, it will take 1 hour to get water to maximum cold temperature.
During this time the compressor will run continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control downward to start cold water flow.
3. Release cold water control once desired fill level is achieved.
Dispensing Hot Water
After setup, hot water will be available in 15-20 minutes.
4. Position bottle, glass, pitcher or cooking pot below spout.
5. Slide red button away from you and depress control downward to
start hot water flow.
6. Release hot water control once desired fill level is achieved.
LIMITED WARRANTY
Primo Water Corporation, ("Vendor") warrants to the original purchaser of this
dispenser, and to no other person, that if this dispenser is assembled and operated
in accordance with the printed instructions accompanying it, then for a period of
one (1) year from the date of purchase, all parts in such dispenser shall be free from
defects in material and workmanship. Vendor may require reasonable proof of your
date of purchase from an authorized retailer or distributor. Therefore, you should
retain your sales slip or invoice. The Limited Warranty shall be limited to repair or
replacement of parts, which prove defective under normal use and service and
which Vendor shall determine in its reasonable discretion upon examination to be
defective. Before returning any parts, you should contact Vendor's Customer
Service Department using the contact information listed below. If Vendor confirms,
after examination, a defect covered by this Limited Warranty in any returned part,
and if Vendor approves claim, Vendor will replace such defective part without
charge. If you return defective parts, transportation charges must be prepaid by
you. Vendor will return replacement parts to original purchaser, freight or postage
prepaid.
The Limited Warranty does not cover any failures or operating difficulties due to
accident, abuse, misuse, alteration, misapplication, improper installation or
improper maintenance or service by you or any third party, or failure to perform
normal and routine maintenance on the dispenser, as set out in the User's Manual.
In addition, the Limited Warranty does not cover damages to the finish, such as
scratches, dents, discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all
warranties for products that are purchased from seller other than authorized
retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS
WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY
WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT,
PUNITIVE, INCIDENTAL, OR CONSEQUENTAL DAMAGES. Vendor assumes no
responsibility for any defects caused by third parties. This Limited Warranty gives
the purchaser specific legal rights; a purchaser may have other rights depending
upon where he or she lives. Some jurisdictions do not allow exclusion or limitation
of special, incidental or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may not apply to you.
Primo Water Corporation
104 Cambridge Plaza Drive
Winston-Salem, NC 27104
866-429-7566
www.PrimoWater.com
TROUBLESHOOTING
Water is leaking.
 Bottle may have a leak that is too large for the Leak Guard feature to stop.
Remove bottle, dispense one quart of water and install new bottle.
 If leak remains, remove bottle and call 866-429-7566 for assistance.
No water is coming from the spout.
 Make sure the bottle is not empty. If empty, replace it.
 Make sure to push the water controls in fully.
Cold water is not cold.
 It takes up to one hour after setup to dispense cold water.
 Make sure the power cord is properly connected to a working outlet.
 Make sure the back of the dispenser is at least 4 inches from a wall and
there is free airflow on all 4 sides of the dispenser.
 Make sure green power switch on back of dispenser is ON.
Hot water is not hot.
 It takes 15-20 minutes after setup to dispense hot water.
 Make sure the power cord is properly connected to a working outlet.
 Make sure red power switch on back of dispenser is ON.
Nightlight Isn't Working
 Make sure the power cord is properly connected to a working outlet.
 Make sure nightlight power switch on back of dispenser is ON.
Dispenser Is Noisy
 Make sure the dispenser is positioned on a level surface.
PN O-046 © 2010 Primo Water Corporation